mm项次NO检查项目Inspection item测试方法图Measuring methoddiagram许可差Permissibledeviation实际测量值Measured value1.1 床台X 轴方向运动之真直度Straightness of theX axismovementa.X-Z面内0.06/1000b.Y-Z面内1.2 床台Y 轴方向运动之真直度Straightness of theY axismovementa.X-Z面内0.06/1000b.Y-Z面内1-1单位Unit : mm项次NO检查项目Inspection item测试方法图Measuring methoddiagram许可差Permissible deviation实际测量值Measured value1.3 床台X轴方向之运动与其上面之平行度Parallelismbetweenmovement in Xaxis directionand table uppersurfaceX≦500 0.02500＜X≦8000.025800＜X≦1250 0.031250＜X≦20000.041.4 床台Y轴方向之运动与其上面之平行度Parallelismbetweenmovement in Yaxis directionand table uppersurfaceY≦500 0.02500＜Y≦8000.025800＜Y≦1250 0.031250＜Y≦20000.041.5 X轴方向运动与床台基准沟侧面之平行度Parallelismbetweenmovement in Xaxis directionand Sidesurface of tablereference slot每300mm的量测距离下许可差为0.015mm0.015for a measuringlength of 3001-2单位Unit : mm 项次NO检查项目Inspection item测试方法图Measuring method diagram许可差Permissibledeviation实际测量值Measured value 1.6各轴方向相互运动之直角度PerpendicularityBetweenmovement in Xaxisdirectionand Yaxisdirectionand Zaxisdirectiona.X-Y轴Place0.012/300b.X-Z轴Place0.012/300c.Y-Z轴Place0.012/3001.7主轴中心线与床台面之直角度Perpendicularity betweencenterline ofmain spindleand tablesurface.旋径每300Per3000.0151-3单位Unit : mm项次NO检查项目Inspection item测试方法图Measuring method diagram许可差Permissible deviation实际测量值Measured value1.8 主轴孔内面之偏摆Run out ofspindle taperhole固定端At spindle side end oftest bar0.005固定端300处At 300 position0.0151.9 主轴轴线与Z轴轴线运动间的平行度Parallelismbetween thespindle axisandthe Z-axismotiona:0.015/300b:0.015/3001.1 0 主轴在Z轴方向之移(松)动量Movement ofmain spindle inZ axis direction0.0051.1 1 主轴端面之偏摆Run out of mainspindle outersurface0.011.1 2 主軸外面之偏擺Run out of mainspindle outersurface0.01mm1.1 3 床檯X軸方向運動之直線度Straightness oftable movementin the X axis.1.Apply a fixed indicator to thestraight edge as the figure shown.2.Adjust to get reading at both endsof the straight edge.2.Move the table 300 mm in X-axisdirection.3.Record the largest value differenceas the measurement value.0.01/3001.1 4 床檯Y軸方向運動之直線度Straightness oftable movementin the Y axis1.Apply a fixed indicator to thestraight edge as the figure shown.2.Adjust to get reading at both endsof the straight edge.2.Move the table 300 mm in X-axisdirection.3.Record the largest value differenceas the measurement value.0.01/3001-41.1 5 旋轉檯旋轉偏擺Tablerunout(XY)0.015mm/3001.1 6 旋轉檯旋轉偏擺Table runout(Z)0.005mm1.1 7 車刀角度換刀後重複定位精度Repeatability oftool angle aftertool change.0.001mm1.1 8 車刀角度停止後重複定位精度Repeatability oftool angle aftertool stop.0.001mm1.2 0 車刀加工後定位精度Repeatability oftool angle aftermachining part0.001mm1.2 1 主軸振動檢測Spindlevibrationdetection≦0.6mm/s(Ref)2.0定位精度检查Positioning accuracy inspection 单位Unit : mm项次NO检查项目Inspectionitem测试方法图Measuring method diagram许可差Permissibledeviation实际测量值Measured value2.1 直线运动之定位精度ISO230-2循环次数:2次Positioningaccuracyof straightlinemovementByISO230-2Cycletimes: TwotimesXL≦10000.011000＜L≦20000.015L≧20000.02YZ2.2 回转运动之定位精度Positioningaccuracyof straightlinemovementByISO230-2Cycletimes: TwotimesC15〞1-73.0反复精度检查Repetition accuracy inspection 单位Unit: sec项次NO检查项目Inspectionitem测试方法图Measuring method diagram许可差Permissibledeviation实际测量值Measured value3.1 直线运动之反复定位精度ISO230-2Positioningrepeatability ofstraightlinemovementByISO230-2Cycletimes: TwotimesX0.006YZ单位Unit: sec3.2 回转运动之重复定位精度ISO230-2Positioningrepeatabilityof straightlinemovementByISO230-2Cycle times: Two timesC 8〞1-83.0反复精度检查Repetition accuracy inspection 单位Unit: sec项次NO检查项目Inspectionitem测试方法图Measuring method diagram许可差Permissibledeviation实际测量值Measured value3.3 Maxreversalvalue最大反沖值Positionaccuracyqualifiedto ISO230-2X0.006YZ4.0循圓精度检查Repetition accuracy inspection 单位Unit: sec项次NO检查项目Inspectionitem测试方法图Measuring method diagram许可差Permissibledeviation实际测量值Measured value循圓精度RoundnessGeometrycontouringXY0.015。