当前位置:文档之家› 美国形位公差标注规定及意义(中英文对照)

美国形位公差标注规定及意义(中英文对照)


4
Goeway eBooks


5
82
A note or specification on the drawing should explain how the part is restrained and the force required to facilitate the restraint. A sample note can be found on the drawing below. /
/
4
M5
A
5
Goeway eBooks


6
82
FEATURE CONTROL FRAME / A feature control frame states the requirements or instructions for the features to which it is attached. /
2
82
NUMBER OF PLACES / COUNTERBORE/SPOTFACE / COUNTERSINK/ DEPTH/DEEP/ SQUARE/ ALL AROUND/ DIMENSION NOT TO SCALE ARC LENGTH/ X BETWEEN/ SLOPE/ CONICAL TAPER/ ENVELOPE PRINCIPLE
Unless otherwise specified, all dimensioning and tolerancing applies in a Free State condition with no restraint. Some parts, such as sheet metal, thin metal, plastics and rubber are no rigid in nature. It may be necessary to specify design requirements on the part in a natural or Free State as well as in a restrained condition. The restraint or force on the nonrigid parts is usually applied in such a manner to resemble or approximate the functional or mating requirements. /

1
82
COMMON SYMBOLS/ Shown below are the most common symbols that are used with geometric tolerancing and other related dimensional requirements on engineering drawings. Note the comparison with the ISO standards. Most of the symbology is identical. There are a few symbols that are used in the ASME Y 14.5, 1994 standard that are being proposed for the ISO standards. The symbols marked with an “ x”are new or revised from the previous Y14.5M, 1982 standard. / ISO ASME Y 14.5, 1994 ISO “ x” Y14.5M, 1982 SYMBOL ASME Y14.5M ISO
Note: This is a change from the previous editions of the Y14.5 standard. The definition of the tolerance zone for the former term tangent radius, previously noted by the symbol R, is now meant to apply to a controlled radius (symbol CR). / Y14.5 R CR
FEATURE CONTROL FRAME DIAMETER/ SPHERICAL DIAMETER/ AT MAXIMUM MATERIAL CONDITION AT LEAST MATERIAL CONDITION REGARDLESS OF FEATURE SIZE PROJECTED TOLERANCE ZONE X X X X X FREE STATE/ TANGENT PLANE STATISTICAL TOLERANCE RADIUS/ CONTROLLED RADIUS / SPHERICAL RADIUS/ BASIC DIMENSION/ (theoretically exact dimension in ISO) ISO X DATUM FEATURE * DATUM TARGET TARGET POINT/ DIMENSION ORIGIN
REFERENCE DIMENDION/ (Auxiliary dimension in ISO) /ISO
NONE/
NONE/
(Proposed) NONE/ R CR SR R NONE/ SR
*
( 50 )
( 50 )
1
Goeway eBooks

ห้องสมุดไป่ตู้

If any of the part specifications are to be verified in a free state, the designer may specify this requirement with the words FREE STATE or the free state symbol. The free state symbol is a F in a circle. The free state symbol means that dimensions and tolerances that have the free state symbol applied are checked in the free state and not in the restrained condition. / F
The free state symbol is applied by placing it next to or associating it with the required dimensions and tolerances. If it is applied in a feature control frame, it always follows the feature tolerance and any modifiers.
8x
8x
NONE
NONE
NONE(implied)/
Note: * May be filled or not filled/ RADIUS, CONTROLLED RADIUS/
*
There are two types of radii tolerance that can be applied, the radius and controlled radius. The radius (R) tolerance is for general applications. The controlled radius (CR) is used when it is necessary to place further restrictions on the shape of the radius, as in high stress applications. / R (CR)
Statistical tolerancing is the assignment of tolerances to related components of an assembly on the basis of sound statistics. An example is: the assembly tolerance is equal to the square root of the sum of the squares of the individual tolerances. /
3
Goeway eBooks


4
82
Note:/ FEATURES IDENTIFIED AS STATISTICALLY TOLERANCED SHALL BE PRODUCED WITH
STATISTICAL PROCESS CONTROLS, OR TO THE MORE RESTRICTIVE ARITHMETIC LIMITS. / In some cases, it may be desirable to state only the statistical tolerance and the arithmetic number will not be shown. In this case, a note such as the following must be placed on the drawing. /
FEATURES IDENTIFIED AS STATISTICALLY TOLERANCED STATISTICAL PROCESS CONTROLS. /
SHALL BE PRODUCED WITH
For additional information on statistical tolerancing, see appropriate statistics or engineering design manuals. / NONRIGID PARTS-FREE STATE CONDITION/ -
相关主题