A B变频器快速调试 Company number：【0089WT-8898YT-W8CCB-BUUT-202108】编辑参数如下1.上电时LCD显示器显示为:Output Freq S→按一次SEL键显示组参数编号及字母.按上下键改变组菜单(Basic Display:b基本显示.Basic Pr0gram :P基本编程.Terminal Block:T端子.Communications:C通信.Advanced progran:A高级编程，Aux Relay Cord: R=Aux Relay Display:d高级显示)。

2.按SEL键进入某组菜单，该组中上次查看时的参数编号将会闪烁。

按上下键可选择主菜单功能，先选择基本显示(Display Groupb)参数按下SEL进入:b001:输出频率ｂ002：命令频率ｂ003：输出电流ｂ：004输出电压ｂ005：直流母线电压ｂ006：变频器状态ｂ007：故障代码1 ｂ008：过程显示ｂ010：输出功率ｂ011：已用电MVVｈｂ012：运行时间ｂ013：转矩电流ｂ014：变频器温度ｂ015：已用电KWｈ以上参数是变频器自动默认不用修改。

3.按上下键可选择主菜单功能，先选基本编程Basic Progran Group按下SEL进入注：这些参数要根据实用的值来进行设定P031：motor NP Volts(电动机铭牌电压) P032：motor NP Hertz (电动机铭牌频率) P033：motor OL current(电动机额定电流)P034：minimum Freq(最小频率) P035：maximum Freq(最大频率)50HZ P036：Start Source(起动源)2-wire 002 P037：Stop mode(停止模式)coast 005 P038:Speed Reference(速度基准值)Analog in1 002 P039:Accel Timel(加速时间为15秒)Sec P040：Decel Timel(减速时间为10秒)Sec P041：Reset to Defalts复位为默认值工Ready/Zdle 000 P042：Auto mode(自动模式) NO Function 003 P043：Motor OL Ret(电机过载值存储)Disabled 0004.按上下键可选择主菜单功能，先选端子 Terminal Block Group按下SEL进入T051:Terminal Block(数字量输入1选择) Digital in1 sel T052:Digital In2sel(数字量输入2选择)Local 003 T053:Digital In3 sel(数字量输入3选择) Clear Fault 010 T054:Digital In4 sel(数字量输入4选择) Comm port 004 T055:Relay out1 sel (继电器输出1选择)Ready/Fault 000 T056:Relay out1 Level (继电器输出1幅值) T058:Relay 1 on Time(继电器1接通On时间) sec T059:Relay 1 offTime(继电器1断开Off时间) sec T060:Relay out 2 sel(数字量输出2选择) motor Running 002T061:Relay out 2 Level (继电器输出2幅值)T063:Relay 2 on Time(继电器2接通On时间) sec T064:Relay 2 off Time(继电器2断开Off时间) secT065: Opto out sel (光电耦合输出选择)At Frequency 001T066: Opto out Level(光电耦合输出幅值)T068: Opto out Logic (光电耦合输出逻辑)T069: Analog In 1 Sel(模拟量输入1选择) 4-20mA 001T070: Analog In 1 LO(模拟量输入1下限)%T071: Analog In 1 Hi(模拟量输入1上限)%T072: Analog In 1 Loss(模拟量输入1丢失)Disabled 000T073: Analog In 2 Sel(模拟量输入2选择) 0-10V 002T074: Analog In 2 LO(模拟量输入2下限)%T075: Analog In 2 Hi(模拟量输入2上限)%T076: Analog In 2 Loss(模拟量输入2丢失)Disabled 000T077: Sleep-wake sel (休眠-唤醒选择) Disabled 000T078: Sleep-Level (休眠等级) 10% T079: Sleep-Time (唤醒时间) SECT080: wake-Level (唤醒等级) 15%T081: wake-Time (唤醒时间) SECT082:Analog out 1 sel (模拟量输出1选择) outFreq 0-10V 000T083:Analog out 1 High (模拟量输出1上限)100%T084:Analog out 1 setpt(模拟量输出1设定点)%T085:Analog out 2 sel (模拟量输出2选择) outcurr 0-10V 001T086:Analog out 2 High (模拟量输出2上限)100%T087:Analog out 2 setpt(模拟量输出2设定点)%T088:Anlg Loss Delay (模拟量丢失延时) SECT089:Analog In Filter (模拟量输入上限)05. 按上下键可选择主菜单功能，先选通信语言Communications Group按下SEL进入C101:Language(通信语言)001 EnglishC102:Comm Format(通信格式)C103:Comm Data Rate(通信数据速率)003 9600C104:Comm Node Addr(通信节点地址)C105:Comm Loos Action(通信丢失动作)C106:Comm Loos Time(通信丢失时间)C107:Comm Write Mode(通信写模式)C108:Start Source2(通信起动命令源2)6.按上下键可选择主菜单功能，先选高级编程Advanced Program Group 按下SEL进入A141:Advanced Program Group(消防强制输入频率)Purge FrequencyA142:Internal Freq(内部频率)60HzA143:Preset Freq0(预置频率0)A144:Preset Freq1(预置频率1)A145:Preset Freq2(预置频率2)A146:Preset Freq3(预置频率1)A147:Accel Time 2(加速时间2) SecA148:Decel Time 2(减速时间2) SecA149:S Curve%(S曲线%)20%A150:PID Trim Hi(PID整定上限)60HZA151:PID Trim LO(PID整定下限)A152:PID Ref sel(PID基准值选择)PID setpoint 001A153:PID Feedback sel (PID反馈值选择)Anaiog In1 000 A154:PID Prop Gain(PID比例增益) 1A155:PID Integ Time(PID积分时间) SscA156:PID Diff Rate(PID微分速率) 1/SecA157:PID Setpoint(PID设置点)50%A158:PID Deadband(PID死区)%A159:PID Preload(PID预负载)A160:PID Process Factor(PID过程因数)A163:Auto Rstrt Tries(自动重新起动尝试)0A164: Auto Rstrt Delay(自动重新起动延时) SecA165:Start At PowerUp (上电起动)Disabled 000A166:Reverse Disable (反向禁止)REV Disabled 001 A167:Flying Start En (飞速起动使能)Disabled 000 A168:Pwm Frequency(PWM频率)A169:Pwm Mode(PWM模式) 2-Phase 001A170:Boost select(升压选择) 004A171:Start Boost(起动升压) %A172:Break Voltage(转折电压)25%A173:Break Frequency(转折频率)A174:Maximum Voltage(最大电压)460 VACA175:slip Hertz @ FLA(满载滑差频率补偿)A176:DC Brake Time(直流制动时间) SECA177:DC Brake Level(直流制动幅值)A178:DC Brk Time@Strt(起动时直流制动时间)A179:Current Limit 1(电流限幅1)A180:Current Limit 2(电流限幅2)A181:Motor Select(电动机过载选择)A182:Drive OL Mode(变频器过载模式)A183:SW Current Trip(软件电流跳闸)A184:Load Loss Level(负载丢失幅值)A185:Load Loss Time (负载丢失时间)A186:Stall Fault Time (堵转故障时间)A187:Bus Reg Mode (总线调节模式)A188:Skip Frequency1(跳变频率1)A189:Skip Freq Band1(跳变频率宽带1)A190:Skip Frequency2(跳变频率2)A191:Skip Freq Band2(跳变频率宽带2)A192: Skip Frequency3(跳变频率3)A193:Skip Freq Band3(跳变频率宽带3)A194:Compensation(补偿)A195:Reset Meters(测量复位)A196:Testpoint Sel(测试点选择)A197:Fault Clear(故障清除)A198:Program Lock (编程锁定)A199:Motor NP Poles(电动机铭牌极对数)A200:Motor NP FLA(电动机铭牌电流)7.按上下键可选择主菜单功能，先选辅助继电器Aux Relay Card Group 按下SEL进入 R221:Relay Out3 Sel (继电器输出3选择)R222:Relay Out3 Level (继电器输出3幅值)R224:Relay Out4 Sel (继电器输出4选择)R225:Relay Out4 Level (继电器输出4幅值)R227:Relay Out5 Sel (继电器输出5选择)R228:Relay Out5 Level (继电器输出5幅值)R230:Relay Ou63 Sel (继电器输出6选择)R231:Relay Out6 Level (继电器输出6幅值)R233:Relay Out7 Sel (继电器输出7选择)R234:Relay Out7 Level (继电器输出7幅值)R236:Relay Out8 Sel (继电器输出8选择)R237:Relay Out8 Level (继电器输出8幅值)R239:Aux Motor Mode (辅助电机模式)R240:Aux Motor Qty(辅助电机数量)R241:Aux 1 Start Freq(辅助1起动频率)R242:Aux 1 Stop Freq(辅助1停止频率)R243:Aux 1 Ref Add(辅助1频率增加)R244:Aux 2 Start Freq(辅助2起动频率)R245:Aux 2 Stop Freq(辅助2停止频率)R246:Aux 2 Ref Add(辅助2频率增加)R247:Aux 3 Start Freq(辅助3起动频率)R248:Aux 3 Stop Freq(辅助3停止频率)R249:Aux 3 Ref Add(辅助3频率增加)R250:Aux Start Deiay(辅助起动延时)R251:Aux Stop Deiay(辅助停止延时)R252:Aux Prog Delay(辅助控制延时)R253:Aux AutoSwap Tme (辅助自动切换延时)R254:Aux AutoSwap Lvl(辅助自动切阀值)8.按上下键可选择主菜单功能，先选辅助继电器Advanced Display Group 按下SEL键进入d301:Control Source(控制源)d302:Control Source(控制输入状态)d303:Comm Display Group(通讯状态)d304:PID Setpnt Displ(PID设定点显示)d305:Analog In 1(模拟量输入1)d306:Analog In 2(模拟量输入2)d307:Fault 1 Code(故障代码1)d308:Fault 2 Code(故障代码2)d309:Fault 3 Code(故障代码3)d310:Fault 1 Time-hr(故障时间1-小时)d311:Fault 1 Time-min(故障时间1-分钟) d312:Fault 2 Time-hr(故障时间2-小时)d313:Fault 2 Time-min(故障时间2-分钟)d314:Fault 3 Time-hr(故障时间3-小时)d315:Fault 3 Time-min(故障时间3-分钟)d316:Elapsed Time-hr(消逝时间-小时)d317:Elapsed Time-min(消逝时间-分钟)d318:Output Powr Fctr(输出功率因数)d319:Testpoint Data(测试点数据)d320:Control SW Ver(控制版软件版本)d321:Drive Type(变频器类型)d322:Output Speed(输出速度)d323:Output RPM(输出速度)d324:Fault Frequency(输出速度) d325:Fault Current(输出速度)d326:Fault Bus Volts(输出速度) d327:Status @ Fault(输出速度)。