These are the characteristics of the 1013 E:Modern water-cooled 4- and 6-cylinder in-line engine Turbocharging with charge air cooling (BFM1013EC/P)High-pressure fuel injection up to 1600 barElectronic engine governor with diagnostic facilities as option 100% PTO capability at flywheel end and front endThree options for installation of gear-driven hydraulic pumps Long maintenance intervals and user-friendly maintenance design Customer service available worldwideThese are the benefits for you:̈High productivity through dynamic power development ̈Quietest engine of its class and high degree of operating comfort ̈Low exhaust emission for a clean environmenẗ1013E .The engine for agricultural equipment.90-186 kW at 2300 rpm...................................................................................................................................................................................................................................................Type of cooling:.......................Crankcase:....................................Crankcase breather:............Cylinder head:...........................Valves/drive train:................Pistons:............................................Piston cooling:..........................Connecting rod:.......................Crankshaft bearings:..........Crankshaft:..................................Camshaft:......................................Lubricating oil:.........................Lubricating oil cooler:........Lubricating oil filter:...........Fuel pump/governor:.........Fuel lift pump:..........................Injection nozzle:......................Fuel filter:......................................Alternator:....................................Starter motor:............................Cab heating:...............................Accessoires:.................................Engine descriptionLiquid cooling,thermostatically controlled,charge-air-cooled engines with air-to-air charge air cooler*Grey cast iron crankcase,for monobloc construction,wet liners Closed circuit crankcase breather Grey cast iron block-type cylinder headOne inlet and one exhaust overhead valve per cylinder,drive through tappets,push rods and rockers;gear-driven camshaft Three ring pistons,two compression rings and one oil scraper ring Oil cooled with spray nozzles Forged steel rodLaminated plane bearingsWith integral counter weights:4-cylinder version with integral mass balancing shafts Forged steelPressure system with integral-gear pump Integral oil to water heat exchanger Canister type paper element full flow filterSingle injection pumps for each cylinder set into crankcaseMechanical centrifugal governor (standard);electronic engine governor (EMR) optional Integrated in v-belt tensioner Six-hole nozzle Replaceable elementThree-phase alternator 12V or 24V 12V or 24VConnections for cab heating in the engine cooling systemCombustion air inlet connections,exhaust connections,positioning of turbocharger,air compressors,hydraulic pump PTOs,SAE 2/3/4/ flywheel housings,flywheels,12 V or 24 V electrics,oil pans,cold start aids3)Without starter motor/alternator, radiator and liquids, however with flywheel and flywheel housing.4)For monobloc construction, please check with DEUTZ AG5)Dimensions without charge air cooler, side mounted turbocharger ̈Technical dataBF4M1013E 4) mm 762593986312295122BF4M1013EC 4) 5)mm 762593986312295122BF6M1013E mm 10555741001281387122̈Standard engines190200210220be P (kW)110100908070605040BF4M1013EBF4M1013EC(g/kWh)n (min )10001200140016001800200022002400–1T (Nm)575550525500475450425400375350190200210220beT (Nm)960920880840800760P (kW)19018017016015014013012011010090(g/kWh)BF6M1013ECP 6108/1307,14617,623009,97186230013,58954*1400800200572180180190200210be P (kW)17016015014013012011010090807060(g/kWh)T (Nm)880840800760720680640600560̈Tractor engines200210220230beT (Nm)860820780740700660620580540P (kW)15014013012011010090807060(g/kWh)200210220230be T (Nm)575550525500475450425400375350P (kW)110100908070605040BF4M1013E BF4M1013EC(g/kWh)n (min )10001200140016001800200022002400–1200210220230be T (Nm)960920880840800760720P (kW)1801701601501401301201101009080(g/kWh)Mechanical and electronic governor (EMR) allow customisation of torque and power curves.Torque back up 0f 30% and more is possible.Drive-away torque of 110% rated torque at 1000 min -1.The engines meet all current and planned exhaust emissions legislations.DEUTZ AGDeutz-Mülheimer Str.147-149 D-51057 KölnTel.:++ 49 (0) 221-822-2510B e s t . -N r . 0 0 3 1 1 7 2 9 / 0 2 / 9 9 / M M -V。