Hydac filter housings a cost effective alternative for replacement elements and the opportunity to change to Pall media
Hydac filter housings without the need for adaptors, whilst for return line applications, by-pass valves are integral to the element.
filter elements bring many benefits:
manufactured and tested to the same
exacting standards as all Pall products. Constructed using ‘Ultipor®’ filter media, Red1000 filter elements provide users access to ISO16889 rated filters to the highest efficiency of ßx(c)≥1000.
Advanced protection by Design
•Proven media technology
•Tapered pore structure for
optimum dirt holding capacity
•PRECISE pore size control
•High strength media bonding and
fibre mix
•High strength media support and
fatigue resistance
•Compatibility with a wide range of
hydraulic fluids and operating
temperatures
Selector Guide
Pall Red1000filter elements are available for use in a wide range of Hydac filter housings.
Pressure-line 'D' Series- Hydac Series 0060, 0110, 0140, 0160, 0240, 0280, 0330, 0500 & 0660 in BN3HC &
BH3HC media.
Return-line 'R' Series- Hydac series as above plus 0500, 0660, 0850, 0950, 1300, 1700 & 2600 in BN3HC media. Use the Selector Guide over the page to identify the correct replacement Red1000element part number. If the Hydac element reference is not listed, please contact your local Pall Sales Office for advice.
filter elements for use
Data Sheet PME RED1000a
* Beta ratios are designated using the symbol (c) to signify they were measured using the ISO 16889 procedure Pall Red1000Series replacement filter elements for Hydac Housings Ultipor III medium
Proprietary resistant, inorganic fibres, resin
bonded into a tapered pore structure.
Specifications Table 1: Pressure Line Series
Hydac Part No Pall Red Part No
Hydac Part No
Pall Red Part No
Because of developments in technology these data or procedures may be subject to change. Consequently we advise users to review their continuing validity annually. Part numbers quoted above are protected by the Copyright of Pall Europe Limited.
, Pall and Ultipor are trade marks of Pall Corporation.
Filtration. Separation. Solution is a service mark of Pall Corporation.Hydac is a registered trademark of Hydac Technology GmbH ® indicates a trademark registered in the USA.© Copyright 2004, Pall Corporation.
December 2004. Printed in England. PMERED1000a/1204
Visit us on the web at /m&e
Pall Corporation has offices and plants throughout the world in locations including:Argentina, Australia, Austria, Belgium, Brazil, Canada, China, France, Germany, India, Indonesia,Ireland, Italy, Japan, Korea, Malaysia, Mexico, the Netherlands, New Zealand, Norway, Poland,Puerto Rico, Russia, Singapore, South Africa, Spain, Sweden, Switzerland, T aiwan, Thailand,United Kingdom, United States, and Venezuela. Distributors are located in all major industrial areas of the world.
Pall Machinery and Equipment Portsmouth - UK
+44 (0)23 9230 3303telephone +44 (0)23 9230 2507fax m&e_sales@
New York - USA +1 516 484 3600telephone +1 888 333 7255toll free +1 516 625 3825
fax
Table 2: Return Line Series with integral
Bypass Valve
Hydac Part No Pall Red Part No
Filter Media:Proprietary resistant inorganic fibres, bonded with epoxy resins.
Filter Hardware:Corrosion protected carbon steel end caps and central core.
Fluid Compatibility:
Compatible with mineral and petroleum oils, water glycols,water-oil emulsions and those synthetic fluids rated for use with fluorocarbon seals.
Operating
Temperature Range:-43°C to 120°C (-45°F to 250°F) with nitrile seals
-29°C to 120°C (-20°F to 250°F) with fluorocarbon seals
Collapse Rating:20 bar (290 psid) minimum differential pressure (210 bar
(3046 psid) minimum for high collapse strength elements).Element performance validated per ISO 16889, ISO 2941,ISO 2943, ISO 3724, ISO 2942, ISO 3968.
Replace ++ with: 50=50psi (3.4 bar),
100=100psi (6.9 bar) - where the Hydac part number ends B6.
Other options available on request.
If the Hydac part number ends with the letter 'V', change the last digit of the Pall part number from 'H' to 'Z'.。