1-port 100M FX 2-Ports
10/100M TX Media Converters
User’s Manual 1．Overview
This Media Converter Complies with IEEE802.3 Standards. It is designed to Convert data signal between 10/100Base-TX and 100Base-FX fast Ethernet. The media converter is connected between Fiber cable and twisted cable segments with network operating smoothly. This converter can be used as a standalone unit or asa slide-in module to the 14 converter rack.
2.Checklist
Before you installing the Switch, verify that the package contains the following：
1．The TP-Fiber Converter
2．AC-DC Power Adapter.
3．This User’s Manual.
Piease notify your sales representative immediately if any of the aforementioned items is missing or damaged.
3. LED Description
There are 6 LED At Front View of 2 port Media Converter
LED Definition Specification
PWR
Indicator of
power
supply
ON when the power supply is
turned on and in normal working
status
FRX
Optical
interface
status
indicator
Bright when optic fiber cable is
connected well, but no data
transmission
Blinking when receiving data
TRX
Ethernet
interface
status
indicator
Bright when twisted pair is
connected well, but no data
transmission
Blinking, when receiving data
FDX
Ethernet
interface
mode
indicator
ON, Full duplex
OFF, Half duplex
4.Technical Specifications
Optical Parameters
Multimode
Fiber 62.5/125, 50/125,100/140µm
Output
optical
power
-20~-14dBm
Receiving
sensitivity
<-31dB
Distance 0~2km or 0~5km
Connector SC, ST, FC
Wavelength 850nm/1310nm
Singlemode
Fiber 9/125,8.3/125,8.7/125or 10/125µm
Distance 0~20km 0~40km 0~60km
Output
optical
power
-12~-8dBm -8~-3dBm -3~ 0dBm
Receiving
sensitivity
< -37dBm < -37dBm < -38dBm
Connector SC, ST, FC
Wavelength 1310nm
Distance 0~80km 0~120km
Output
optical
power
-3~ 1dBm -3~ 2dBm
Receiving
sensitivity
< -38dBm < -38dBm
Connector SC, ST, FC
Wavelength 1550nm(DFB)
when less than 15km, use attenuator
5.Installing the Converter
For as a standalone unit
a)Verify the AC-DC adapter conforms to your country
AC Power requirement and insert the power plug
b)Connect the media cable for network connection
for as a slide-in unit
c)The slide-in Media Converter and Converter Rack
should be supplied only form the same source, both
Media Converter and Rack are built to match each
other at dimensions, DC jack, DC receptacle and
power safely
d)Turn off the 19” converter rack power
e)Ensure that there is no activity in the network
f)Locate +5VDC power jack on converter back,
carefully slide in and plug to 19” rack +5VDC
power receptacle
g)Connect the media cable for network connection
h)Turn on the converter rack power , the Power LED
will light up
6.Cable Connection Parameter
100Base-X network allows 512-bit time delay between any two node stations in a collision domain. The overall Bit-time
of TP/Fiber wires and devices must be within 512bit in a segment. You may use a switch to break up collision domain and extend the cabling distance.
●TP Cable Limitations：Cat.5 100m
●Multi-mode Converter Fiber Cable Lions：
SC/ST/FC/LC Multi-mode Converter Models：
Multi-mode
Full-duplex
Node to Node ：2Km
Node to Switch ：2Km
SC/ST/FC/LC Single Mode Converter Models：
SC．S20
Full-duplex
Node to Node ：20Km
Node to Switch ：20Km
7.TP-Fiber Technical Specifications
●Standards:
I EEE802.3 IEEE802.3u 10/100Base-TX 100Base-Fx
●TP Port: RJ45
●UTP Cable: Cat.5 cable up to 100m
●Wavelength: 1310nm/1550nm
●Fiber cable(um):
50/125,62.5/125,or 100/140/um multi-mode
8.3/125,8.7/125,9/125/or10/125/um single-mode
●Max distance:
Singlemode:20~120km
Multimode: 2km
●LED Indicators:
FDX, TRX FRX,PWR
●Data Transfer Rate:
Speed Forwarding Rate
100Mbps 148,800PPS
10Mbps 14,880PPS
*Flow Control:IEEE802.3x compliant for full-duplex Back
pressure flow control for half-duplex
* Power Requirement:2A@+5VDC
*Ambient Temperatur e:0 to 60℃
* Humidity:5% to 90%
*Dimensions: 25(H)70 (W)94(D)mm
●Note: Connecting to Router, Bridge, or Switch, please
refer to the device's Technical Manual。