0.01% 0.05% 0.10%
0.10% 0.25% 0.50%
0.01% 0.05% 0.10%
0.10% 0.25% 0.50%
-55 ~+155
Characteristics
Specifications Item (GB/T 5729-2003) Test Method(GB/T 5729-2003)
1/16W
1/16W
1/10W
1/8W
1/4W
1/4W
1/2W
Max.Working Voltage(V)
25
50
100
150
150
150
150
Max.Overload Voltage(V) TCR(PPM/ )
50 5 10
50 ~5K ~12K
100 5 5 10
50 25
200 5 5 10
50 25
300 5 5 10
50 25
300 5 5 10
50 25
300 5 5 10
50 25
300 5 5 10
50 25
5
~15K ~100K
~30K ~200K
~50K ~400K
~50K ~500K
~100K ~500K
~100K ~500K
Resistance Range
50
Resistance Tolerance Operating Temperature Range
Item 0603 0805 1206
Power Rating
1/10W
1/8W
1/4W
Max.Working Voltage(V)
75
150
200
Max.Overload Voltage(V) TCR(PPM/ )
5
150
300
400
10 15
25 50
5
10 15
25 50
5
10 15
25 50
R
0.5%R+0.05
JIS-C-5202-7.1 -65 1 45 1 Hour,-65 ,followed by 45minutes of RCWV JIS-C-5202-6.1.4 (Duration):10s 1s (Bending Distance): 0402 0603 0805 1206 3mm 1812 2010 2512 1mm
2
(
) ,rated load (power rating or current rating) shall be derated
THIN FILM CHIP FIXED RESISTORS
RATINGS
Item 0402 0603 0805 1206 1210 2010 2512
Power Rating
Resistance Range
50
~15K
25
~100K
10
~332K
50
~30K
25
~200K
4.7
~1M
50
~50K
25
~400K
4.7
~1M
Resistance Tolerance Operating Temperature Range
0.01% 0.05% 0.10%
0.10% 0.25% 0.50%
MIL-STD-202F Method 210E 270 5 10 1 270 5 10s 1s
PACKAGING
Tape and reel Paper taping 0402:
T.C.R
within specified T.C.R
MIL-STD-202F Method 304 +25/-55/+25/+125/+25 JIS-C-5202-7.2 2.5 5 RCWV2.5 or Max Overload Voltage, whichever is lower, for 5 seconds MIL-STD-202F Method 301 1 Apply Max Overload Voltage for 1 minute MIL-STD-202F Method 302 100V 1 Apply DC 100V between substrate and termination for 1 minute, then check insulation resistance MIL-STD-202F Method 107G -55 ~150 100 -55 ~150 100 cycles
Bending Strength
R
0.05%
R
0.2%
Solder-ability
95% Min coverage
MIL-STD-202F Method 208H 240 5 2 0.5 240 5 2s 0.5s
Resistance to Soldering Heat
R
0.05%R+0.05
R
0.2%R+0.05
Resistance Value Code (E-24 )
Resistance Tolerance Code
Packing Style Code Code Packing Style
Three digits (E-24 series): The first two digits are significant figures and the third one denotes number of zeros. (E-96 ) Four digits (E-96 series): The first three digits are significant figures and the four one denotes number of zeros. R Decimal point should be expressed by "R". Example 103=10K E-24 1003=100K E-96 1R0=1.0
Applications
Medical Equipment Test/Measurement Equipment Printer Equipment Automatic Equipment Controller Converters Communication Device Mobile phone etc.
10~100KFra bibliotek10~332K
4.7
~1M
Resistance Tolerance Operating Temperature Range
0.10%
0.25%
0.50%
-55 ~+155
Special Ratings
Item 0402 0603 0805 1206 1210 2010 2512
Power Rating
DERATING CURVE
- 55 100 Percent ratedload 75 50 25 Operating Temperature Range -55 155 70
-75
-50
- 25
0
25
50
75 (
100 )
125
155
Ambient temperature 70 For resistors operated in ambient over 70 in accordance with the above figure.
R
0.5%R+0.05
4
Characteristics
Specifications Item (GB/T 5729-2003) Test Method(GB/T 5729-2003)
R Steady state humidity
0.05%R+0.05
R
0.3%R+0.05 MIL-STD-202F Method 103B 40 2 90~95%RH 1000 40 2 90~95%RH 1000h JIS-C-5202-7.2 155 96 96 hours @155 without load
1000M
Min
Temperature Cycling
R
0.05%R+0.05
R
0.25%R+0.05
R 70 Load Life
0.05%R+0.05
R R
0.20%R+0.05 0.5%R+0.05
For resistance value>7K :
:For thin film chip resistor with high power series:
1/16W
1/16W
1/10W
1/8W
1/4W
1/4W
1/2W
Max.Working Voltage(V)
25
50
100
150
150
150
150
Max.Overload Voltage(V) TCR(PPM/ )
50
100
200
300
300
300
300
25 PPM/
50 PPM/
Resistance Range
Thin film chip fixed resistors
Code 02 03 05 06 1210 10 12
Type Type 0402 0603 0805 1206 1210 2010 2512 0402 0603 0805 1206 1210 2010 2512 D E F G H Code
Code T A B C D F