SS-2004(有需要联系分享者)填隙胶2004 —— 导热硅胶Gap Filler 2004Thermally Conductive Silicone Rubber产品描述Product DescriptionSS-2004是一种混合比为1:1的双组分硅橡胶。
它性能优异，适用于诸如PC 主板上这类狭小空间内电子元件的散热。
经混合后可实现室温固化，或在有热源的条件下，5分钟内即可完成固化。
SS-2004 is a high performance thermally conductive liquid gap filling material. It is formulated to develop a soft, form in place elastomer ideal for coupling hot PC board components to heat sinks. It is supplied as a two part, 1:1 mix ratio silicone that when mixed, cures at room temperature, or when exposed to heat results in a cured elastomer in 5 minutes.产品特点Product Features►100%固体成分 100% solids liquid ►无气味、无副产物 No odor or byproducts ►混合比1:1，使用方便 Convenient 1:1 mix ratio ►铂催化加成反应Platinum addition cure ►导热系数高，为2.0W/m ·K High2.0W/m ·Kthermal conductivity典型应用Typical Applications ►电子元件散热Electronic component thermal dissipation ►电子元件耦合Coupling electronic components ►散热点胶Form in place heat sink固化机理Chemical cure system 铂催化下的加成固化反应Platinum catalyzed, addition Cure System性能参数Typical Properties固化前 组分A 组分B 颜色： 白色 粉红色 黏度（厘泊）： 150,000 150,000 比重： 2.8 2.8 粘稠性（混合后）： 膏状 釜中寿命（分，室温）： 60 表干时间（分，室温）： 120 表干时间（分，100℃）： 5 UNCURED Part A Part B Color White Pink Viscosity, cps 150,000 150,000 Specific Gravity 2.8 2.8 Consistency mixed: Paste Pot-life @ R.T .: 60 minutesCure time @ R.T.: 120 minutes Cure time @ 100 C 5 minutes 固化后硬度（邵氏00）：70 绝缘强度：19.7KV/MM（500V/mil）介电常数（100赫兹）：7 体积电阻率（欧姆/米）：1012燃烧等级UL94 V-0 导热系数（瓦/米·开）： 2.0 CUREDShore 00 70 Dielectric Strength, volts/mil 500 Dielectric Constant, 100Hz 7 Volume Resistivity, Ohm/M 1012 Flame Rating 94 V-0 Thermal Conductivity, W/m·K 2.0 混合说明Mixing Instructions最佳混合方式是使用静态混合器以体积比1:1混合。
The preferred method of mixing and application of SS-2004 is by using a 1:1 mix ratio by volume dispensing unit through a static mixer.操作注意Handling precautions本品的固化机理为铂催化加成反应，与以下物质接触不利于固化过程：含硫化合物（如硫醇、硫化物、硫酸盐类、含硫的有机物橡胶）、含氮化合物（如胺类、亚胺类、氨化合物、叠氮化合物）、金属锡及锡的化合物、锡催化固化机理的橡胶组分等。
This is a Platinum Cure system product. The catalyst can be deactivated by exposure to sulfur containing compounds like thiols, sulfides, sulfates, organic rubber containing sulfur, nitrogen containing compounds like amines, amides, imides, azides, tin metals or compounds, or tin cured RTV’s.固体成分Solids100%，不含溶剂成分100% solids, contains no solvents温度范围Service Temperature-45至250℃-45 to 250℃附着力Adhesion对大多数金属和常见基底不需要打底层即有很好的附着力。
Primerless adhesion to most metals and typical substrates.使用限制Limitations待完全固化后再使用工件。
确保施用空间内有足够剂量。
Allow to fully cure before putting assembly into service. Ensure enough product remains between flanges to be effective in an assembly.包装规格PackagingSS-2004采用两支装。
有400毫升、36.28千克（80磅）等规格。
此产品也可根据客户需求，采用其他包装规格。
SS-2004 is available in 400 ml. dual syringes and 80 lb. kits. This product is also available in customer defined packaging sizes, upon request.操作及安全Handling and safety暂不使用时将容器密封以延长保存期。
避免孩童接触。
未固化的产品对眼睛和皮肤有刺激作用。
参考安全技术说明书（MSDS）。
For maximum shelf life, keep containers sealed when not in use. Keep out of the reach of children. Uncured sealant irritates eyes and skin. Refer to MSDS.保质期Shelf-life自发货日起，厂家承诺密封条件下1年的保质期。
请在低于22℃（70F）且干燥环境下贮存。
Sealed containers are guaranteed for 1 year from the ship date when stored in a cool dry area below 70 F. 有限承诺Limited warranty此处提供的表述、技术数据及推荐意见信息是根据我们的测定如实提供的，并相信是准确且可靠的。
但由于使用本公司产品的条件和方法非我们所能控制，因此本信息不能取代客户进行的操作，以承诺产品是安全、有效、并完全满足于特定的最终用途。
用户应根据自身情况及试验来判断产品是否达到使用效果，并自行承担产品的使用责任及风险。
我们所提供的使用建议，不得被视为侵犯任何专利的误导。
我们的唯一保证，是产品在发货时满足的销售规格及剂量。
如果该保证不能兑现，您所能获得的补偿仅限于退还被保证产品的购货价款或重新更换。
特别声明，对于其它特别用途或商品的任何明示或暗示的适用性不作任何保证。
我们对买家或第三方的任何事故或由此引起的损失不负任何责任。
我们对在本文中未作出陈述的其他书面说法也不作承诺保障。
All recommendations, statements and technical data herein are based on tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as warranty, either expressed or applied. User shall rely on his own information and tests to determine suitability of the product for the intended use, and the user assumes all risk and liability resulting from the use of this product. Manufacturer’s sole respons ibility shall be to replace that portion of product of the manufacturer proves to be defective. Manufacturer shall not be liable to the buyer or any third party for injury, loss or damage directly or indirectly resulting from the use of, or inability to use, the product. Recommendations or statements other than those contained in a written agreement signed by an officer of the manufacturer shall not be binding by the manufacturer.该产品并未经过黏膜组织、破损皮肤、血液、或植入人体内等领域的测试，也不推荐使用于以上领域。