当前位置:文档之家› 美国海宝_精细等离子切割机_HPR130_系统安装手册_中文版

美国海宝_精细等离子切割机_HPR130_系统安装手册_中文版


构成
7
开关阀总成 • 开关阀总成必须安装在离割枪1.2 m之内.
割枪 • 提升架必须离割枪51 mm之内. • 割枪和提升装置在 “X” 和 “Y”轴上.
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
构成
2
电源 • 用铲车移动电源时确保铲起整个电源 • 放置电源的地方要求自然通风 • 要保持电源的前后完全通风. • 不要安装其它的滤网,避免影响冷却。
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
Interfacing
17
Machine motion 这是一个可能的配置:
HPR130 J300 CNC
+24 VDC +24 VDC IN (+) +24 VDC OUT (-) Pin #23 Pin #4
DC Com
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
可选的 Command Interface
12 Command Interface Board I/O PCB
Torch (-) Work (+) J2B J2A J300B J300A
P/S Control Board
CNC
Command THC Console
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
气路系统
5
气源 • 如果使用普通的气源可以使用一个高质量的单调节阀 ,如果使用高压力的气体应该使用高质量的双调节阀. • 调节器应该安装在离气体控制箱3 m之内 • 如果气管长度在23 m之内那内径应为9.5 mm.如果超 过23 m 那么内径应为12.5 mm.
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
THC其他的选项 THC其他的选项
14
装配 “voltage divider” 或者其他的在机器的右侧
使用现有的弧压提供给弧压板. 连接#25线 弧压: 使用现有的弧压提供给弧压板 连接 线 (yellow)从I/O PCB的 Work接头 从 的 接头 到弧压板的TB1 的#2 位置 连接 位置.连接 连接#26线 (yellow and black)从I/O PCB的 Torch接头 到弧压板的 线 从 的 接头 到弧压板的TB1 的#1 位置 位置. 到弧压板的
增加冷却液
11
为了让冷却液能充满割 枪:
压下和保持安培调整开关… 压下和保持安培调整开关 监测流量当超过0.7的时候松 监测流量当超过 的时候松 开同时泵应该继续工作. 开同时泵应该继续工作 压下电源开关和保持在 ON (I) 的位置
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
Hypertherm的 isolation amplifier PCB 将提供1/50th 的真实弧压 用于调高控制系统
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
Interfacing
15
Machine motion • 详见Rev. 0 HPR130 安装手册 (page 3-22) • 电源到CNC interface 电缆:
– 电源的 pin 23 必须是收到一个正24 VDC – 电源的 pin 4 必须没有什么 – 电源的 pin 4 不能连接公共的24VDC
割枪的连接
高频箱
9
Pilot arc lead (++)
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
Electrode lead (-)
割枪的连接
自己连接
• 注意这有两个尺寸的连接片在连接电缆上. (同样的备件号)
10
Ignition console or table
Power supply
• 注意这有两个尺寸的连接片在引导弧电缆上.
Ignition console
Power supply
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
THC其他的选项 THCБайду номын сангаас他的选项
13
Divided Voltage(+) Divided Voltage(-)
120AC Hot 120AC Return
Isolation Amplifier PC Board Hypertherm P/N 041274
Arc Voltage(-) Arc Voltage(+)
气路系统
6
气源压力 • 所有气体的初始压力应达到8 bar. • 对保护气设定气体控制器到Test Pre-flow 然后调整到8 bar. • 对等离子气设定气体控制器到Test Cut Flow然后调整 到8 bar.
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
构成
3
点火箱 • 点火箱必须安装在离电源45 m之内. • 点火箱必须安装在离割枪15 m之内. • 点火箱可以安装在电源内也可以安装在台架上.
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
AC 电源 通过连接线提供 电源: 通过连接线提供120 VAC 给弧压板 连接 PCB2 上的 给弧压板. 上的J2.1的 pin #15 的
电源分配板)到弧压板的 电源. 电源分配板 到弧压板的 REC1 的pin #6 提供 AC 电源 连接 PCB2的 J2.1 的pin 的 #15到 REC1 的 pin #5. 到
(
分配电压: 使用1/50th 的弧压在弧压板的 的弧压在弧压板的REC2上. Pin #1 是 DC正极 pin #2 是 正极, 分配电压 使用 上 正极
DC 负极 pin #3是接地 是接地. 是接地
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
系统安装
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any form without the permission of Hypertherm, Inc.
相关主题