※ X directional linearity = ( ΔEx /ΔExa-b ) × 100[%] Y directional linearity = ( ΔEy /ΔEya-b ) × 100[%]
※Test Tool: Brass Finger
[測試工具]:黃銅手指
Cylindrical brass bar simulating a fingertip used in measurement and testing.
[手觸]
FPC
03. General Specification
[規格總則]
Item [項目]
(1) Frame Size [外框尺寸]
(2) View Area [可視區]
(3)
Active/Precision Area
[動作區]
(4)
Total Thickness
[總厚度]
(5) Tail Length [出線長度]
[模擬指尖，由黃銅製成，為測量和測試]
(2) Specification [規格] linearity must be meet the electrical specification outlined in Item 6
[線性必須符合 6 項目的電性規範]
[觸擊測試]
Specification [規格] 100,000,000 times (1 億次)
Date: Sep. 07, 2011 Version:2.04.01
Page: 6 / 18
08. Mechanical
Item [項目]
Characteristics
[機械特性]
Operating
04. Environmental Characteristics
[環境特性]
Item [項目]
(1) Operation [操作]
(2) Storage [儲存]
Specifications [規格]
Temperature
[溫度]
Humidity [濕度] (Non Condensing)
[不可結露]
Page: 8 / 18
10. Linearity：
[線性]
(1) Linearity Condition [線性測試條件]
Measure the product output data when a brass finger connected with GND is traced a straight line AB. ΔE is the maximum output difference when a brass finger traces A to B. AB is the end and the end in an active area. Linearity is expressed by the following equation. (Fig 10-1)
(1) Force
[作動力]
(2) Impact [撞擊]
Condition [條件]
Specification [規格]
Finger≦10g
[手觸≦10g]
Satisfy1.Optical
Characteristics.
25.0ψDIA. Steel Ball/67g
2.Electrical
Height=30cm / 1 time, Impact at Characteristics.
[-40°C /120 小時，回常溫 4 小時後始可測試]
-40°C ~80℃ [60 min./cycle] *10 cycles and normalized for 4 hrs
[-40°C ~80°C，每循環 60 分鐘，共 10 次循環，回常溫 4 小時後始可測試]
Date: Sep. 07, 2011 Version:2.04.01
[範圍]
[此規格適用於投射電容式觸控屏幕]
02. Features
[特性]
Item [項目] (1) Type
[型式]
(2) Input Mode [操作模式]
(3) Connector [連接方式]
Specifications [規格] Projective Capacitive
[投射電容式]
Finger
Page: 2 / 18
SPECIFICATION REVISION RECORD 規格變更記錄
Customer [客戶名稱]： Customer NO. [客戶編號]：
NO. Version. Date
[項次] [版本]
[變更發行日期]
Date [發行日期]： Sep. 07, 2011 Model [型式]：T150S-XDN042G-3S02R0-059PN
(6)
I/O Channel
[出線 pin 腳數]
Specifications [規格] 346.00±0.30 X 270.00±0.30 mm 305.00±0.20 X 229.00±0.20 mm 306.20±0.20 X 230.20±0.20 mm 2.45±0.30 mm 59.00±3.00 mm X=40pin / Y=33pin
Heat Cycle (2) [高溫循環]
Cold Cycle (3) [低溫循環]
(4) Thermal Cycle [冷熱循環]
70°C /120 hrs and normalized for 4 hrs
[70°C /120 小時，回常溫 4 小時後始可測試]
-40°C /120 hrs and normalized for 4 hrs
[恆溫恆濕]
Condition [條件]
Specification [規格]
70°C X 90%RH, 120 hrs Satisfyand normalized for 4 hrs 1.Electrical
Characteristics.
[70°CX90%RH，120 小時，回常溫 4 小
時後始可測試]
-Appendix Ⅰ [附註一]：Design Guide [設計指南]……………………….……… 16/17
-Appendix Ⅱ [附註一]：Appearance Specification [外觀檢查規格]…………...… 18
Date: Sep. 07, 2011 Version:2.04.01
90% ± 3%
(2) Haze [霧化度]
< 2%
※measured by BYK-Gardner
06 Electrical Characteristics
[電子特性]
Item [項目] (1) Response
[作動時間]
(2) Insulation [絕緣阻抗]
(3) Linearity [線性]
Tail (6) Bending
[繞折]
90°10 times left & right
[90°角,左右來回 10 次]
Date: Sep. 07, 2011 Version:2.04.01
Page: 7 / 18
09. Reliability
[信賴性]
Item [項目]
Constant
(1)
Temperature /Humidity
7H pencil, pressure 750g/45°
[鉛筆 7H,壓力 750g/45°(ASTM D3363)]
(4) Hardness [硬度]
Tail (5) Peeling
[剝離]
800g/cm by vertical 90° for 30sec
[800g/cm , 垂直 90°，靜置 30 秒]
-20°C ~ +70°C 20%RH~85%RH
-40°C ~ +80°C 10%RH~90%RH
Note: Testing environment is under normal atmosphere pressure.
[註:於正常的 1 大氣壓下]※When the ambient temperature is above 65°C, the humidity is allowed to be below 50%RH .
TABLE OF CONTENTS 目錄
00. Specification Revision Record [規格變更記錄].……………………………………… 03 00. Dimension Drawing [尺寸圖].…………………………………………………. ……… 04 01. Circumscription [範圍].…………………………………………………………………. 05 02. Features [特性].…………………………………………………………………………….. 05 03. General Specification [規格總則].………………………………………………………... 05 04. Environmental Characteristics [環境特性].……………………………………………. 05 05. Optical Characteristics [光學特性].……………………………………………………… 06 06. Electrical Characteristics [電子特性].…………………………………………………… 06 07. Durability [耐久性].…………………………………………………………………. ……… 06 08. Mechanical Characteristics [機械特性].………………………………………………... 07 09. Reliability [信賴性].…………………………………………………………………………. 08 10. Linearity [線性].………………………………………………….………………………….. 09 11. Appearance Inspection [外觀檢查].……………………………………………………… 10 12. Attention for Mounting Condition [裝機注意事項].……………………………..………. 11 13. Caution [注意事項].…………………………………………………………………………... 12/13 14. Warranty [保固].……………………………………………………………………………. 14/15 15. Appendices [附註].………………………………………………………………………… 15