Sub：多层板常规叠层规定为节约成本，规范叠层，特对叠层规定如下：（客户对叠层有要求除外）压板厚度＝内层芯板厚度＋内层半固化片厚度＋内层所有铜厚＋外层铜箔厚度1、压板厚度＝成品厚度+0.05/-0.075mm2、内层半固化片厚度按阻抗规范要求计算（其取值随相邻两铜面情况不同而变化）。

3、对于铜面情况与规定不一致或非常规铜厚情况，需在该规定基础上调整。

18um 、35 um 、70 um 铜箔厚度7628（0.185mm），2116（0.105mm）1080（0.075mm）3313（0.095mm） 半固化片厚度一、 四层板（其中2、3层全部是GND层）(1)成品板厚要求：0.5+/-0.10MM___________________ 18UM___________2116*1___________________ 0.13mm 35/35um___________2116*1____________________18um理论压板厚:0.46mm(2)成品板厚要求：0.8mm+/-0.10mm___________________ 18UM___________1080*1____________2116*1_______________0.25mm 35/35um____________2116*1____________1080*1_____________________18um理论压板厚:0.71mm(3)成品板厚要求：1.0MM+/-0.10MM____________________ 18UM___________1080*2________________0.51mm 35/35um____________1080*2_____________________18um理论压板厚:0.89mm(4)成品板厚要求:1.6+/-0.15MM_____________________ 18UM___________1080*1____________7628*1_______________1.0mm 35/35um____________7628*1____________1080*1_____________________18um理论压板厚:1.54mm(5)成品板厚要求:2.0+/-0.20MM_____________________ 18UM___________1080*2理论压板厚:1.92mm(6)成品板厚要求：2.5+/-0.20MM_____________________ 18UM___________1080*1____________2116*1_______________2.0mm 35/35um____________2116*1____________1080*1______________________18um理论压板厚:2.41mm(7) 成品板厚要求：3.0+/-0.20MM_____________________ 18UM___________1080*1____________7628*1________________2.40mm 35/35um____________7628*1____________1080*1_______________________18um理论压板厚:2.95mm二、 六层板（第2、5层为铜面）(1) 成品板厚要求：0.70+/-0.10MM____________________ 18UM___________2116*1________________0.13mm 18/18um___________2116*1________________0.13mm 18/18um____________2116*1_____________________ 18UM理论压板厚:0.68mm(2) 成品板厚要求：0.80+/-0.10MM____________________ 18UM___________2116*1________________0.13mm 35/35um___________2116*1________________0.13mm 35/35um____________2116*1_____________________ 18UM理论压板厚:0.75mm(3) 成品板厚要求：1.0+/-0.10MM_____________________ 18UM___________1080*2________________0.21mm 35/35um___________2116*1理论压板厚:0.96mm(4) 成品板厚要求：1.6+/-0.15MM______________________ 18UM___________1080*1___________7628*1________________0.36mm 35/35um___________7628*1________________0.36mm 35/35um___________7628*1___________1080*1_______________________ 18UM理论压板厚:1.56mm(5 成品板厚：2.0+/-0.20MM______________________ 18UM___________1080*1___________7628*1________________0.51mm 35/35um___________7628*1___________1080*1________________0.51mm 35/35um___________7628*1___________1080*1_______________________ 18UM理论压板厚:1.92mm(6 成品板厚要求：2.4+/-0.20MM______________________ 18UM___________1080*1___________7628*1________________0.71mm 35/35um___________7628*1___________1080*1________________0.71mm 35/35um___________7628*1___________1080*1_______________________ 18UM理论压板厚:2.32mm(7 成品板厚要求：3.0+/-0.20MM______________________ 18UM___________1080*1___________2116*1________________1.2mm 35/35um_______________________ 18UM 理论压板厚:2.92mm三、八层板(2、4、6层为GND层)(1 )成品板厚：1.0+/-0.10MM______________________ 18UM___________2116*1________________0.13mm 18/18um___________2116*1________________0.13mm 18/18um___________2116*1_________________ 0.13mm 18/18um___________2116*1_________________________18UM理论压板厚:0.96mm(2 )成品板厚：1.6+/-0.15MM______________________ 18UM___________1080*2________________0.25mm 35/35um___________7628*1________________0.21mm 35/35um___________7628*1_________________ 0.25mm 35/35um___________1080*2_________________________18UM理论压板厚:1.56mm(3)成品板厚：2.0+/-0.20MM______________________ 18UM___________1080*1___________2116*1________________0.36mm 35/35um___________1080*2________________0.36mm 35/35um___________1080*2_________________ 0.36mm 35/35um___________2116*1___________1080*1_________________________18UM理论压板厚:1.92mm(4)成品板厚：2.4+/-0.20MM______________________ 18UM___________1080*2________________0.51mm 35/35um___________7628*1_________________________18UM 理论压板厚:2.37mm(5)成品板厚：3.0+/-0.20MM______________________ 18UM___________1080*2________________0.71mm 35/35um___________7628*1________________0.71mm 35/35um___________7628*1_________________ 0.71mm 35/35um___________1080*2_________________________18UM理论压板厚:2.98mm四、十层板（2、5、6、9层为GND层）(1)成品板厚：1.3+/-0.15MM_______________________ 18UM___________2116*1________________0.13mm 18/18um___________2116*1________________0.13mm 18/18um___________2116*1_________________ 0.13mm 18/18um___________2116*1__________________ 0.13mm 18/18um___________2116*1__________________________18UM理论压板厚:1.24mm(2)成品板厚：1.6+/-0.15MM_______________________ 18UM___________1080*2________________0.13mm 35/35um___________2116*1________________0.21mm 35/35um___________2116*1_________________ 0.21mm 35/35um___________2116*1__________________ 0.13mm 35/35um___________1080*2__________________________18UM理论压板厚:1.58mm(3)成品板厚：2.0+/-0.20MM_______________________ 18UM___________1080*2________________0.21mm 35/35um___________7628*1________________0.21mm 35/35um___________7628*1_________________ 0.21mm 35/35um___________7628*1__________________ 0.21mm 35/35um___________1080*2__________________________18UM理论压板厚:1.94mm(4)成品板厚：2.4+/-0.20MM_______________________ 18UM___________1080*1___________7628*1________________0.25mm 35/35um___________7628*1________________0.25mm 35/35um___________7628*1_________________ 0.25mm 35/35um___________7628*1__________________ 0.25mm 35/35um___________7628*1___________1080*1__________________________18UM理论压板厚:2.32mm(5)成品板厚：3.0+/-0.20MM_______________________ 18UM___________1080*1___________7628*1________________0.36mm 35/35um___________7628*1________________0.36mm 35/35um___________7628*2_________________ 0.36mm 35/35um___________7628*1__________________ 0.36mm 35/35um___________7628*1___________1080*1__________________________18UM理论压板厚:2.93mm十二层:（2、4、9、11层为GND层）(1)成品板厚：1.6+/-0.15MM_______________________ 18UM___________2116*1________________0.13mm 35/35um___________2116*1________________0.13mm 35/35um___________2116*1_________________ 0.13mm 35/35um___________2116*1__________________ 0.13mm 35/35um___________2116*1__________________0.13 mm 35/35um____________2116*1__________________________18UM理论压板厚:1.65mm(2)成品板厚：2.0+/-0.20MM_______________________ 18UM___________1080*2________________0.13mm 35/35um___________2116*1________________0.21mm 35/35um___________2116*1_________________ 0.21mm 35/35um___________2116*1__________________ 0.21mm 35/35um___________2116*1__________________0.13mm 35/35um____________1080*2__________________________18UM理论压板厚:1.94mm(3)成品板厚：2.4+/-0.20MM_______________________ 18UM___________1080*2___________2116*1________________0.21mm 35/35um___________7628*1________________0.21mm 35/35um___________2116*1_________________ 0.21mm 35/35um___________2116*1__________________ 0.21mm 35/35um___________7628*1__________________________18UM理论压板厚:2.32mm(4)成品板厚：3.0+/-0.2MM_______________________ 18UM___________1080*1___________2116*1________________0.36mm 35/35um___________2116*1________________0.36mm 35/35um___________2116*1_________________ 0.36mm 35/35um___________2116*1__________________ 0.36mm 35/35um___________2116*1__________________0.36mm 35/35um____________2116*1____________1080*1__________________________18UM理论压板厚:2.94mm六、十四层板(2、4、6、9、11、13层为GND层)(1)成品板厚：2.0+/-0.20MM_______________________ 18UM___________2116*1________________0.13mm 35/35um___________2116*1________________0.13mm 35/35um___________2116*1_________________ 0.13mm 35/35um___________2116*1__________________ 0.13mm 35/35um___________2116*1__________________0.13mm 35/35um____________2116*1___________________0.13 mm 35/35um____________2116*1__________________________18UM理论压板厚:1.95mm(2)成品板厚：2.50+/-0.20MM_______________________ 18UM___________1080*2________________0.21mm 35/35um___________2116*1________________0.21mm 35/35um___________2116*1_________________ 0.21mm 35/35um___________2116*1__________________ 0.21mm 35/35um___________________0.21 mm 35/35um____________1080*2_______________________18UM 理论压板厚:2.48mm(3)成品板厚：3.0+/-0.20MM_______________________ 18UM___________1080*1___________7628*1________________0.21mm 35/35um___________7628*1________________0.21mm 35/35um___________7628*1_________________ 0.21mm 35/35um___________7628*1__________________ 0.21mm 35/35um___________7628*1__________________0.21mm 35/35um____________7628*1___________________0.21 mm 35/35um____________7628*1____________1080*1__________________________18UM理论压板厚:3.0mm七、十六层板(2、4、6、8、9、11、13、15层为GND层)(1)成品板厚：2.2+/-0.20MM_______________________ 18UM___________2116*1________________0.13mm 35/35um___________2116*1________________0.13mm 35/35um___________2116*1_________________ 0.13mm 35/35um___________2116*1__________________ 0.13mm 35/35um___________2116*1__________________0.13mm 35/35um____________2116*1___________________0.13 mm 35/35um____________2116*1___________________0.13 mm 35/35um____________2116*1__________________________18UM理论压板厚:2.20mm(2)成品板厚：2.5+/-0.20MM_______________________ 18UM___________1080*1___________7628*1________________0.13mm 35/35um___________2116*1________________0.13mm 35/35um___________2116*1_________________ 0.13mm 35/35um___________2116*1__________________ 0.13mm 35/35um___________2116*1__________________0.13mm 35/35um____________2116*1___________________0.13 mm 35/35um____________2116*1___________________0.13 mm 35/35um____________7628*1____________1080*1__________________________18UM理论压板厚:2.48mm(2)成品板厚：3.0+/-0.20MM_______________________ 18UM___________1080*1___________2116*1________________0.21mm 35/35um___________2116*1________________0.21mm 35/35um___________2116*1_________________ 0.21mm 35/35um___________2116*1__________________ 0.21mm 35/35um___________2116*1__________________0.21mm 35/35um____________2116*1___________________0.21 mm 35/35um____________2116*1___________________0.21mm 35/35um____________2116*1____________1080*1__________________________18UM理论压板厚:2.90mm。