200米深水井施工方案滤料、封闭止水材料的准备井壁管(滤水管)采用φ273mm×6m的管材,其中滤水管长度为60m。
滤料选用直径为5~7mm的圆砾石,要求无结块、无杂质。
封闭止水材料选用优质粘土球,对于深度超过10m的部分进行封闭止水。
4、钻探、成井工艺在施工中,使用滨州BZCCD350ZYⅡ型钻机进行钻探作业,配备BW850/2A泥浆泵和XXXHOWO水车20立方水车、雷诺6吨随车吊一部。
钻探过程中,应根据地层情况及时调整钻具和钻头,保证施工的顺利进行。
同时,在出渣和排浆量大的情况下,应设立3个浆池,包括沉淀除砂池、循环池和泥浆储备池,以保证施工的顺利进行。
5、潜水泵的安装在井深达到200m后,进行潜水泵的安装。
根据实际情况选择合适的潜水泵进行安装,保证水量的充足供应。
6、工期及人员安排施工工期约为60天,根据实际情况安排工程师、技术人员和施工人员,保证施工进度和质量。
7、安全生产、文明施工在施工过程中,要严格遵守安全生产规定,加强现场安全管理,保证施工人员的生命财产安全。
同时,要注重文明施工,保持施工现场的整洁和环境卫生。
8、服务承诺本工程承诺在施工过程中,保证施工质量和进度,同时提供完善的售后服务,确保客户满意。
为了满足设计要求,井壁管选用了规格为Φ273mm×6mm的螺旋管。
在众多滤水管中,我们建议选择桥式滤水管,因为它耐久且孔隙率大,规格为Φ273mm×6mm,桥孔缝隙为0.75~1mm。
滤料的选择要符合设计要求,本工程选用了直径为5~7mm的砾石。
在选购时,我们要求圆砾直径必须符合要求,无结块和杂志,无粉状物。
计算滤料用量时,我们采用公式V=a×(D2~d2)×H×π/4,其中V为滤料用量,a为充盈系数,取111~1125,D为钻孔直径,d为井壁管外径,H为填砾高度。
为了保证钻孔垂直度和了解地层结构,我们采用了分二级成孔的方法。
第一级成孔直径为Φ400mm,使用Φ393.7mm牙轮钻头和Φ159×4.5m钻铤;第二级成孔达到设计口径,使用Φ593.7mm牙轮钻头和Φ159×4.5m钻铤。
我们采用组合牙轮钻头钻进采用时减压钻进,扩孔时钻头连接导向装置确保钻孔垂直度。
钻孔应保持垂直,每百米钻孔倾斜度不大于1.5°。
同时,我们使用了Φ425mm×10mm长约4.5m的管材加工捞渣筒。
在开孔前,我们要配制好泥浆,严禁用清水开孔。
泥浆材料用优质粘土,处理剂用氢氧化钠或碳酸钠,泥浆密度控制在1.15~1.20 kg/L之间、粘度18~25s。
开孔钻进应使用开孔钻头,采用低钻压、低钻速、中泵量钻进,保证开孔垂直且不塌。
钻进到可加入第一级钻具时,更换钻具,刚开始钻进采用低钻压、低转速、中泵量,正常后采用常规钻进参数,大钻压、中转速、大泵量钻进。
在钻进过程中,我们要根据钻进速度、钻具运转情况及孔内返出泥浆中携带的钻渣进行地层判别并详细记录。
钻至预定孔深后,我们要测量钻具校正XXX。
在采集地层样品前,需要进行钻进参数的调整。
对于粘土类地层,中钻压、中转速、大泵量是适合的参数;而对于砂类地层,轻钻压、慢转速、大泵量是更好的选择。
在钻进松散层时,控制泥浆的粘度和含砂量至关重要。
现场需要进行除渣和替浆、排浆的工作。
泥浆性能参数的范围应该是相对密度1.15~1.25,粘度18~25 s,钻屑含量低于8%。
计算每立方泥浆材料用量时,可使用以下公式:V = q×H×k,其中V代表水泥用量,q代表单位长度套管容积,k代表附加系数(一般为1.3-1.5)。
在扩孔钻进至设计孔深后,需要进行清孔工作,以降低泥浆中的无用固相含量(小于4%),将孔口泥浆密度降至1.20 kg/L以下,然后进行破壁处理,并下入捞渣筒进行捞渣。
根据地层结构,应先下入沉淀管,然后下入滤水管和井壁管(滤水管安置位置应对应于含水层)。
在下管时,每隔10m应安装一组扶正器,可使用混凝土预制块或直径为14~16mm的圆钢制作。
扶正器的高度应该是h=[(D-d)/2]-0.15,其中h代表扶正器高度,D代表钻孔直径,d代表井壁管外径。
井壁管连接有两种方法,一种是丝扣连接,另一种是电焊焊接。
建议采用电焊焊接法,但必须符合强度要求且无大于1mm的砂眼。
桥式滤水管采用穿孔垫筋缠丝包网,穿孔方法是在井管上呈梅花形圆孔,孔径为18mm,滤水管孔隙率为30%,井管底部用6mm后钢板封底。
填砾时,应采用静水填砾法,以防止砾料中途堵塞而出现“架桥”现象。
填砾不宜过快,应一锹一锹填砾,并观察井壁管内返浆情况。
填砾高度应比设计高度高出5~8m。
如果出现“架桥”现象,应及时处理,可以使用活塞上下抽拉或钻具间歇性短时间回转敲打井壁管来解桥。
止水时,应使用预泡后团成30~40mm直径的优质粘土球均匀地投入井壁管与钻孔的环状间隙,填厚约10m。
然后使用活塞在井壁管内进行抽拉,观察井壁管内外水位变化情况。
如果井壁管外的水位不发生变化,说明止水成功,然后继续投粘土球至护筒底部。
最后,进行洗井、抽水和实验等工作。
After gravel and sealing。
the water filter pipe n in the wellbore pipe is pulled using a piston。
and the water level changes are observed。
If the water level is different from the original level。
the pump is lowered and water is pumped out while measuring dynamic and static water levels and water output。
After the dynamic water level stabilizes。
the pump is raised。
and the XXX pulled again。
and the debris XXX water for 48 hours while measuring hydrogeological parameters such as dynamic and static water levels and water output。
Water samples are taken for full analysis and sent to the Chad nal Laboratory for testing.If the water output cannot meet the requirements。
XXX aquifer for soaking for more than 20 hours。
and the clay and siltin the aquifer can be washed out using an air XXX.4.10 On-site recordingCarefully record the drilling log and report。
XXX record the depth。
thickness。
leakage。
seepage。
collapse。
and block ns of each aquifer。
and conduct a full-hole record.5.n of submersible pumps5.1 Submersible pump requirementsThe XXX brand submersible pump (with an outer diameter of less than or equal to ф150mm。
a head of 50-200m。
and a drainage capacity of 50-90 m3/h) is installed according to the water output and approved by the owner.5.2 High head XXX:1) The water inlet of the pump must be below 1 meter from the dynamic water level。
and the lower end of the motor must be at least 0.3 meters above the well bottom.2) When the rated power is less than or equal to 15KW and the voltage is 380±5‰。
the motor can be started at full voltage.3) When the rated power is greater than 15KW。
the motor is XXX.4) XXX and fill the motor with clear water。
Pay n to preventing false filling。
tighten the bolts。
XXX.5) Corresponding lifting tools。
such as tripods and chains。
should be prepared.6) Install XXX and start-up equipment。
and start the motor instantly (within one second) to see if the motor XXX。
If it is opposite。
interchange any two joints。
Then install the protective wire board and water filter。
and prepare to go down the well。
When testing the motor and pump n。
clear water must be poured from the pump outlet。
and the water can be started when the water flows out of the inlet.6.le。
XXX。
and equipment6.1 XXXComplete within 22 days from the approval ofXXX(Attachment 1: n progress chart)6.2 XXXOne person is responsible for the project。