当前位置:文档之家› 路由器配置手册

路由器配置手册

路由器设置指南
本指南主要针对现场的工程人员,描述了CISCO路由器的设置和应用。

一、准备工作
1.打开包装箱,取出路由器及其附属线缆(包括电源线、兰色的控制线)。

2.连接控制线:将兰色控制线的一头(RJ45)插在路由器后面板的“CONSOLE”
口(兰色的),另一头(DB9串口)插在计算机的COM1上。

膝上型计算机
路由器专用控制线
3.插上路由器电源线。

4.打开计算机。

进入超级终端程序(开始—程序—附件—通讯(Communications)—超级终端)。

新建一个连接:
(1)输入新建连接的名称,如ROUTER。

(2)选择COM1口。

(3)设置波特率(每秒位数)=9600;数据位=8;奇偶校验=无;停止位=1;
流控制=无。

5.关闭一切使用COM1串口的应用程序。

如果COM1口坏,则可以换成COM2口进行路由器设置。

二、路由器设置步骤
1.打开路由器电源。

2.超级终端画面中会出现如下路由器自检画面,这时说明路由器工作正常。

若超级终端画面中无反映,敲击回车键,若仍然无反映,则说明此路由器硬件或内部操作系统(IOS)有问题。

速与有关人员联系。

(1)路由器为新的(未曾设置过)
System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
C1700 platform with 32768 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x30ccc4
Self decompressing the image :
##################################################################### ##################################################################### ##################################################################### ##################################################################### #####################################################################
##################################### [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at F AR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DF ARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-Y-M), Version 12.1(3)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Wed 19-Jul-00 14:51 by ccai
Image text-base: 0x800080DC, data-base: 0x80629784
cisco 1720 (MPC860) processor (revision 0x601) with 24576K/8192K bytes of memory
.
Processor board ID JAD04420EEV (3015268710), with hardware revision 0000
M860 processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Low-speed serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]:
此时,键入“NO”回车,出现如下字样:
Would you like to terminate autoinstall?[yes]:
此时,键入“YES”回车,直到出现“Router>”的字样。

此时,键入“ENA”回车,出现“Router#”的字样。

(2)路由器曾经被设置
对于这种情况,路由器启动后出现:
Press RETURN to get started!
键入回车,直到出现“Router>”的字样。

此时,键入“ENA”回车,输入密码,出现“Router#”的字样。

此时,键入“erase star”回车。

此时,键入“confirm”回车。

当出现“Erase of nvram: complete”时,关路有器。

重新启动路由器,此时情况如同(1)。

3.用“写字板”软件打开车站路由器对应的配置文件
4.将所该文件的内容全部选定,并拷贝。

5.到超级终端画面中,当出现“Router#”时,鼠标右键点击“粘贴到主机”6.等屏幕不再变化时,输入命令copy run startup-config
7.重新启动路由器。

8.设置完毕。

相关主题