M – 160 所有电缆、气管和电线 Update 都必须使用线缆托架
cables, tubing and workpieces.
Note: Exceptions will be announced
at the briefing for each task.
M – 70
工具不得遗留到站上或 工作区域地面上。 Tools must not be left on the stations or the floor of workspace.
M – 130 工作站之间的最大间 距需≤5mm Maximum distance between stations: <= 5 mm
M – 140 所有型材末端必须安装 盖子。 All ends of profiles must be fitted with caps.
M – 150 固定任何一段线槽时都 应使用至少2个带垫圈的 螺丝。 Use at least 2 screws with washers to secure any section of cable channel.
M - 40 线缆托架的间距为 ≤120mm。 Distance between cable holders: < = 120 mm
M – 45a 电缆/电线/气管绑在线 夹子上 。 The only acceptable method for binding Cable
单根电线用绑扎带固定在线夹子上
M – 30 扎带的间距为≤50mm。这 一间距要求同样适用于 型材台面下方的线缆。 PLC和系统之间的I/O布 线不在检查范围内。 Distance between cable ties: <= 50 mm. This also applies to cables under the profile plate. I/O cabling between PLC and system will NOT be checked.
世界技能大赛
机电一体化项目专业技术规范
机械部分 MechanicalPP-Leabharlann Nr.okM - 10
型材板上的电缆和气管必 须分开绑扎。 Cable and tubes must be
routed separately on the
profile plate.
not ok
M – 15
当电缆、光纤电缆和气管 都作用于同一个活动模 块时，允许绑扎在一起。 It is allowed to route tubes, electrical and optical cables together when they go to a moving module.
shortest pneumatic
connection to the first
cable tie:
60 mm +/- 5mm
M – 60
所有活动件和工件在运 所有驱动器、线缆、气管和工件需能够 运行期间，不允许驱动器、线缆、
动时不得发生碰撞。 自由运动。
线管或工件间发生接触。
All actors and
注意：如有例外，将在每个任务开始前 Contact between actuators, cables,
workpieces have to move 的例会中进行通知。
tubing or workpieces during
without collisions.
Free movement of all actuators, operation.
M – 20 扎带切割后剩余长度需
≤1mm，以免伤人。
A
Remaining length of cut
cable ties, A: Risk of
injury
A <= 1 mm
M – 21
New 新增
Cable ties on the input and output side of a flexible cable duct / drag chain
软线缆或拖链的输入
和输出端需要用扎带
固定。
M – 25 所有沿着型材往下走的线 缆和气管（例如PP站点处的 线管）在安装时需要使用线 夹固定。 All cables and tubes going downwards on a profile e.g. at the “Pick & Place” station have to be mounted with cable clips.
and modules must be
secure.
All signal terminations
must be secure.
M - 100
不得丢失或损坏任何零 部件或组件（其中包括 电缆、线路等等） No parts or components
should be lost or damaged
(including cables, lines
M - 80
工作站上不得留有未 使用的零部件和工件。 Unused components and
workpieces must be
removed from the
stations.
M - 90
所有系统组件和模块 必须固定好。所有信号 终端也必须固定好。 All system components
and so on).
Components lost or damaged during completion of task 完成任务期间出现组件丢失或损坏
M – 110 站与站之间的错位需小 于等于5 mm 。 Station misalignment: <= 5 mm
M – 120 工作站的连接必须至少 使用 2 个连接件。 Adjoining stations must be connected with at least 2 connectors.
单根电缆/电线/气管没有紧固在线 夹子上
/ Wire / Optical Cables / Tubes is to use conducted cable holders.
M – 50 Update
第一根扎带离阀岛气 管接头连接处的最短 距离为 60 mm +/- 5 mm。 Distance from the