SPECIFICATION电源适配器规格书FOR SWITCHING AC ADAPTERPRODUCT 产品名称： AC-DC ADAPTER 电源适配器发行行印印MODEL 产品型号：MTP051CC-0510EPART NO 产品编号：C109-6234REV 版本: A1CUSTOMER 客户 :斯莱普ISSUE DATE 发行日期： 2013-9-26受领印栏*未签回而下订单即视同认可!工程品管业务发行部核伟审黄弯经鑫署栏准核办SHENZHEN MOUNTPOWER INDUSTRY CO., LTD.No 2, 2Road, XiaoShan Industrial Park, HuangPu, Shajing Town, Shenzhen City, ChinaTEL: +86-5 FAX: +86-0Website：.lxsepu.DOCUMENT NO:C109-6234 A1 PAGE 1 OF 13 3/27/2014CONTENTS 容1. Scope 围 (4)2. Electrical Requirements 电性能要求 (4)2.1 Input Voltage Requirements 输入特性 (4)2.1.1 Input Voltage 输入电压................................................... (4)2.1.2 Input Voltage Range 输入电压围 (4)2.1.3 Input Current 输入电流 (4)2.1.4 Input Frequency 输入频率 (4)2.1.5 Inrush Current 浪涌电流 (4)2.1.6 Power Efficiency 效率 (4)2.1.7 Leakage Current 漏电流 (4)2.1.8 Power Factor 功率因数 (4)2.2 Output Voltage Requirements 输出特性 (5)2.2.1 Normal DC Output Voltage 输出空载电压 (5)2.2.2 DC Output Voltage Range 额定负载输出电压 (5)2.2.3 Load Current Range 额定输出电流 (5)2.2.4 Peak Load Current 峰值电流 (5)2.2.5 Ripple & Noise 纹波 (5)2.2.6 Hold-UP Time 保持时间 (5)2.2.7 Turn-ON Delay Time 延迟时间 (5)2.2.8 Dropout Time 回动时间 (5)2.2.9 Line Regulation Rate 线性调整率 (5)2.2.10 Load Regulation Rate 负载调整率 (5)2.2.11 Transient Response 瞬态响应 (5)2.2.12 Voltage Drift 电压飘移 (5)2.3 Protection 保护 (5)2.3.1 Out Over Current Protection 过流保护 (5)2.3.2 Short Circuit Protection 短路保护 (5)DOCUMENT NO:C109-6234 A1 PAGE 2 OF 13 3/27/20142.3.3 Over Temperature Protection 过温保护 (5)2.3.4 Output Voltage Protection 输出过压保护 (5)2.4 Green Mode Requirement 绿色电源要求 (5)2.5 Isolation Requirements 绝缘要求 (6)2.5.1 HI-POT 高压要求 (6)2.5.2 Insulation Resistance 绝缘电阻…..................................................... .62.5.3 Insulation Class 绝缘等级 (6)3. Safety & EMC Requirements 安规标准要求 (6)3.1 EMI/EMS 电磁兼容干扰... ............................................................... (6)3.2 Safety Requirements 安规要求 (6)4. Environmental Requirements 使用环境要求 (6)4.1 Temperature 温度.............................................................................................. (6)4.2 Humidity 湿度 (7)5. Reliability 可靠性 (7)5.1 Calculated MTBF 平均间隔故障时间估算 (7)5.2 Demonstrated MTBF 证明MTBF (7)5.3 Useful Life 使用寿命/有效期 (7)5.4 Burn-In 煲机 (7)5.5 Ac Plug Strength AC 插头强度 (7)5.6 DC Cord Bending 直流电源线的弯曲 (8)5.7 Temperature Up With 温度与 (8)5.8 Vibration 震动测试... ..................................................................... ..85.9 Drop Test 跌落测试……………………………………………………….............................. ..86. Mechanical Requirements 机械特性............................................................................. (9)6.1 AC Input Type 初级输入插头类型......................................................... ..................... ..9 6.2 DC Output Type 次级输出插头类型 (9)6.3 DC Output Cable 次级输出线类型............................................................................ (9)6.4 Weight 产品重量 (9)6.5 Case Material 外壳线材 (9)6.6 PCB Material 线路板材料 (9)6.7 Outline Dimension 外形尺寸 (10)6.8 Marking and Labeling 铭牌标准 (11)7. Packing 包装 (12)DOCUMENT NO:C109-6234 A1 PAGE 3 OF 133/27/20148. Modify 修改 (12)1.0 Scope 围This specification defines the functional requirements and characteristics ofMTP051CC-0510E AC-DC Switching power supplies.该产品规格书定义产品 MTP051CC-0510E 属于开关电源的功能要求及特性要求2.0 Electrical Requirements 电性能要求*TEST MEASURES 测试方法C1：0.1uF CERAMICS CAPACITOR 瓷片电容; C2：10uF 50V ALUMINUM CAPACITOR 电解电容2.1 Input Voltage Requirements 输入特性ITEM SPECIFICATION MIN TYP. MAX项目规格/测试条件最小额定最大1.NORMAL INPUT VOLTAGE(Vrms) SINGLE PHASE 单相额定输入电压2. INPUT VOLTAGE RANGE(Vrms) SINGLE PHASE 单相100 240输入电压围3. INPUT CURRENT(A)输入电流TYPICAL INPUT VOLTAGE& OUTPUT AT FULL LOAD输入最大电流0.54. INPUT FREQUENCY(Hz) SINGLE PHASE 单相47 50 63输入频率5. INRUSH CURRENT(A) TYPICAL INPUT VOLTAGE& OUTPUT AT FULL LOAD , 25℃.浪涌电流在室温 25 度，额定电压输入和满载输出6. EFFICIENCY(%) TYPICAL INPUT VOLTAGE& OUTPUT AT FULL LOAD效率额定电压输入和人满载输出DOCUMENT NO:C109-6234 A1 PAGE 4 OF 13 3/27/20147. LEAKAGE CURRENT(mA) TYPICAL INPUT VOLTAGE泄露电流额定电压输入8. POWER FACTOR TYPICAL INPUT VOLTAGE& OUTPUT AT FULL LOAD功率因数额定电压输入和满载输出2.1.9 INPUT FUSE 保险丝输入电路:The hot line side of the input shall have a fuse 在火线一边连接一颗保险丝2.1.10 INPUT PROTECTION DEVICE 输入保护装置:An adequate internal fuse on the AC input line shall be provided. 安装在火线部线路的保险丝提供保护作用2.2 Output Voltage Requirements 输出特性ITEM SPECIFICATION MIN TYP. MAX项目规格/测试条件最小额定最大1.NORMAL DC OUTPUT VOLTAGE(V)额定输出电压2. DC OUTPUT VOLTAGE RANGE(V)额定负载输出电压TYPICAL OUTPUT VOLTAGE 输出额定电压5.04.75.33. LOAD CURRENT RANGE (A)额定0 负载电流4. PEAK LOAD CURRENT(A)峰值电流5. RIPPLE & NOISE(mV)纹波6. HOLD-UP TIME(ms)保持时间7. TURN-ON DELAY TIME(ms)延迟时间8． DROPOUT TIME(ms)回动时间9. LINE REGULATION RATE (%)线性调整率25℃.定电压输入和额定电流输出额定输出电流，从电压输入围没 10V 调整，输出变化DOCUMENT NO:C109-6234 A1 PAGE 5 OF 133/27/201410. LOAD REGULATION RATE (%)负STEP LOAD CHANGE IS 0.1 A/µsec.载调整率额定输入电压，从额定输出电流从 0A 开始调整到额定电流，输出电压变化11.TRANSIENT RESPONSE TIME(ms) STEP LOAD CHANGE IS 1 A/µsec. 10%-90%-10%的负载瞬态响应时间12. VOLTAGE DRIFT RATE (%) TYPICAL INPUT VOLTAGE AND TYPICAL LOAD CURRENT , 25电压漂移率℃.2.3 Protection 保护ITEM SPECIFICATION MIN TYP. MAX 项目规格/测试条件最小额定最大1. OUT OVER CURRENT PROTECTION(A)输出过流保护The power supply shall be protected against output overloads. Thepower supply is not damaged or life degraded by continuous operationin output overloads.当产品电流输出一定的电流围，产品进入打嗝模式，产品自动保护，解除短路后，产品自动恢复正常2.52. SHORT CIRCUIT PROTECTION产品短路保护The power supply shall be protected against short circuits. The powersupply is not damaged or life degraded by continuousoperation in short circuit.产品不管在输出轻载还是满载情况下，短路输出端产品会自动保护，并且去掉断开保护后，产品恢复正常Pa3. OVER TEMPERATURE PROTECTION N/A过温保护4.Output Voltage Protection(v) When the power supply output voltage over 15V,the power supply N/A 8输出过压保护Protection 产品在输出一定的电压围会自动保护2.4 Green Mode Requirements 绿色能效要求2.4.1 When the switching power supply working on stand by mode and no loads, the inputpower will less than 0.3 W.当产品在额定输入电压，空载输出的时候，功率损耗小于 0.3W.2.5 Isolation Requirements 绝缘要求ITEM 项目SPECIFICATION OR TEST CONDITION 规格/测试条件ACCEPTANCE CRITERIA 接受标准1.HI-POT 高压测试INPUT TO OUTPUT, 1500Vac 60 SECONDS 5mA NO DAMAGE输入对输出，1500 伏交流点时间为 60 秒，设置电流为 5MA 不损坏2.INSULATION RESISTANCE INPUT TO OUTPUT,DC 500V >10MΩ绝缘电阻测试输入对输出直流 500V3. INSULATION CLASS INSULATION CLASS OF TRANSFORMER CLASS B绝缘等级变压器绝缘系统，符合 UL 要求3. Safety & EMC Requirements 安规标准要求ITEM 项目SPECIFICATION OR TEST CONDITION规格/测试条件ACCEPTANCE CRITERIA接受标准1.EMI/EMS 电磁兼容干扰MEET EN55022 EMC2.SAFETYREQUIREMENTS MEET EN60950 CE，GS安规4. Environmental Requirements 环境要求ITEM 项目SPECIFICATION OR TEST CONDITION MIN TYP. MAX规格/测试条件最小额定最大1.OPERATINGTEMPERATURE 定电流输入和额定电流输出0℃40℃操作温度2. STORAGE TEMPERATURE -20℃85℃存储温度4. OPERATING HUMILITY NON-CONDENSING 5%RH 90%RH操作湿度5. STORAGE HUMILITY NON-CONDENSING 5%RH 90%RH存储湿度5. Reliability 可靠性ITEM SPECIFICATION OR TEST CONDITION ACCEPTANCE CRITERIA项目规格/测试条件接受标准1. CALCULATED MTBF MEET MIL-HDBK-217F 30000 HOURS满足 mil-hdbk-217fMTBF 计算30000 小时2. DEMONSTRATED MTBF TYPICAL INPUT&FULL LOAD , 25℃50000 HOURS平均间隔故障时间估算在室温 25 度，额定输入和输出的条件下50000 小时EFUL LIFE有效期限TYPICAL INPUT&FULL LOAD, 40℃典型的输入和满负荷 40°1YEARS ABOVE 一年以上TYPICAL INPUT&FULL LOAD, 25℃典型的输入和满负荷 25°2YEARS ABOVE 两年以上4. BURN-IN 煲机AT 30℃(±10℃),NORMAL INPUT VOLTAGE 2~4 HOURS2-4 小时在温度为 30+-10 度的环境5.AC PLUG STRENGTH AC 插头强度THERE MUST NOT BE SHAKING AND WIRE BREAKINGWHEN 98N IN 1 MINUTE IS ADDED TO THE AC PLUG FTO EVERYDIRECTION。