P/ LINE
Cavity
PL
Core
蓝色为PL线 Blue line is PL line.
Customer comment. (please give your approval and comments) OK or NG remark Approval by: date
Notes: please advice any concern on propose parting line.
Customer comment. (please give your approval and comments) OK or NG remark Approval by: date
X
？
？ ？
Customer comment. (please give your approval and comments)
Y
Z
OK or NG
remark
Approval by:
date
Gate layout
三点位置针阀式热嘴转搭底进胶 3 point valve gates turn to edge gate
Shrinkage
Y
X
Notes: above shrinkage is estimated according to our understanding, pls correct it if there is any risk of getting right dimension
Shrinkage with orientation
N/A N
Core steel Slider steel Lifter and small insert steel
S50C/1.2343 S50C/1.2343
Family with:
S401
Cosmetic finishing
N/A
1.2344
Customer comment. (please give your approval and comments) OK or NG remark Approval by: date
Notes: please advice any concern on propose parting line.
Parting line
P/ LINE
此处建议做3度左右减胶拔 模，模具上需插穿 We suggest reduce plastic to increase the draft angle to 3 degree.
Cavity and core Impression
Core Cavity
Tool information
Need your input and correction to below information:
Resin material : PP LGF 40 Resin supplier: Ticona Celstran PPResin Grade LGF 40-2 Hot runner 针阀式转冷流道进胶 Tool type : 2 plate Gate type : 3 point valve gates Automatic: turn to edge gate 666G Cavity steel YES No. of Hot Tip 3 point HRS Or Synventive
Parting line
确认是否能 更改（客户 不能理解此 处具体意思 ）；客户回 复分型线有 问题，都是 放在最下面 的，不会出 现插穿面， 乐新下来根 据客户意见 重新分析
P/ LINE
参考 Cavity S301
PL
Core
蓝色为PL线 Blue line is PL line.
目前没有插穿角度，为简化分型面， 此处做5°以上插穿（左右两侧） This position do not have shut off angle. For To simplify the parting line, we suggest make 5 degree shut off shutoff angle. (Both side are Customer comment. (please give your approval and comments) the same) OK or NG remark Approval by: date
Notes: this is very rough layout, but it is a Useful guidance for our tool designer.
Benchmark Location
出模方向 Demolding direction 客户确认所有安装孔 都是一个方向
Parting line
/ S401 Rear Frame
Thickness : PM/PE DFM by: Checked by:
2MM
/
XIAO qing
RE V
Date
Update or added sliders
95_23335_A01
Remark:
3D Rev
95_23335_A01____FRAME_REAR_CA_S401______________3DORG____1
S401 Rear Frame DFM CAD version number：95_23335_A01
Product information
产品尺寸 Product size：311.06*935.6*62.4
Segment : Project name : Part name : Part No:
Tonnage
N/A
Runner Sys:
No. of Gate. (Each part) Forecast volume (shot) No. of Cavity:
3
Part weight (g) :
S50C/1.2343
N/A 1
Special tool : Cosmetic par. (please give your approval and comments) OK or NG remark Approval by: date
Part Layout
Need to show part layout to avoid customer misunderstood our proposal Tool top