承插焊管件（一）Socket Welding FittingsGB/T 14383、SH 3410、HG/T 21634、ASME B16.11、JIS B2316公称通径Nominal Pipe Size 承插孔深度Depth ofSocket壁厚Wall Thickness中心至承插孔底Center to Bottom of SocketAC min90°弯头、三通、四通90°Elbow、Tee、Cross45°弯头45°ElbowDN NPS J min SCH803000SCH1606000XXS9000SCH803000SCH1606000XXS9000SCH803000SCH1606000XXS90006 8 10 1/81/43/81010103.23.34.03.54.04.4---------111114111416---------8888811---------15 20 25 1/23/411013134.55.05.66.07.08.09.510.011.516192219222725283211131413141816192132 40 50 11/411/221313166.36.47.08.09.011.012.013.014.027323832384135385418212521252922252865 80 100 21/2341616198.910.010.012.513.8------------4157675764------------2932413235------------·本表列出的为承插焊管件各相同部分尺寸，不同标准规定的接管尺寸及承插孔径d1、流通孔径d2尺寸见承插焊管件的接管外径、承插孔径及流通孔尺寸表。
·当产品为异径时，流通孔d2的尺寸用异径公称通径相对的d2尺寸、中心至承插孔底的尺寸A与同径管件相同。
·The above list shows sizes of the same parts of SW fittings.The sizes of different codes pipes,socket diameter d1 and bore diameter d2 refer to the list of the pipe outside diameter,socket diameter and bore diameter of SW fittings.·As to the reducing fittings,size of the bore diameter d2 applies to the relevant size d2 of the reducing norminal pipe size,size of center to thebottom of socket A issame to the straight fittings,承插焊和螺纹活接头Unions of Socket-Welding&ThreadedHG/T 21634、MSS SP-83公称通径Nominal Pipe Size外径End DIA壁厚Wall Thickness螺母厚度Nut螺帽每英寸的螺纹扣数Threads Perinch球面凸缘厚度MaleFlange定位口高度Bearin公称装配长度Length AssemNominat结构尺寸LayingLength流通孔径Bore D min C minG min H F min h min LE d2DN NPS 承插焊Socket螺纹Thread承插焊Socket螺纹Thread承插焊Socket螺纹Thread6 8 10 1/81/43/821.821.825.914.719.122.93.23.33.52.53.13.23.23.23.51616143.23.23.51.51.51.54141462121247.410.913.915 20 25 1/23/4131.237.145.527.733.541.44.14.35.03.84.04.63.74.14.51411113.74.14.61.51.81.949576224293017.522.228.432 40 50 11/411/2254.961.575.250.657.270.15.35.66.14.95.15.65.25.66.41010105.45.96.62.22.32.771778637383936.542.453.965 80 21/2391.7109.285.3102.47.78.37.17.77.18.0887.58.33.13.6102109565965.379.9·活接头适用于3000及3000以下级别；管件级别代号与管子壁厚等级的关系见后。
·接管尺寸承插孔径d1、流通孔径d1、流通孔径d2和承插孔深度J与ASME B16.11 规定相同。
·Unions only applie to the class 3000 and below it; the relations of pressure grade and schedule refer to hereafter.·Dimensions of pipe,socket diameter d1,bore diameter d2 and the length ofthe depth of socket J are same to requirements of ASME B16.11.承插焊管件的接管外径、承插孔径及流通孔径尺寸表List of The Pipe Outside Diameter,Socket Diameter and Bore Diameter fo SW Fittings螺纹管件Threaded Fittings GB/T 1426、ASME B16.11公称通径Nominal Pipe Size90°弯头、三通、四通90°Elbows、Tees、Crosses45°弯头45°Elbows所有管件All Fittings中心至端面Center to End中心至端面Center to End端部外径Outside Diameter of Band最小壁厚Minimum Wall Thickness 螺纹长度Length of Thread MinA G D CDN NPS SCH802000SCH1603000XXS6000SCH802000SCH1603000XXS6000SCH802000SCH1603000XXS6000SCH802000SCH1603000XXS6000B L26 8 10 1/81/43/82121252125282528331717191719221922252222252225332533383.183.183.183.183.303.516.356.606.986.48.19.16.710.210.415 20 25 1/23/412833383338443844512225282528332833353338463846564656623.183.183.684.094.324.988.158.539.9310.912.714.713.613.917.332 40 50 11/411/2244516051606460648333354335434443445256627562758475841023.894.014.275.285.567.1410.5911.0712.0917.017.819.018.018.419.265 80 100 21/2347686106839511495106114526479526479647979921091461021211521211461525.615.996.557.658.8411.1815.2916.6418.6723.625.927.728.930.533.0螺纹管件Threaded Fittings GB/T 1426、ASME B16.11公称通径Nominal Pipe Size 管箍、半管接头Couplings、Boss管帽Caps所有管件All Fittings 端面至端面End to End端面至端面End to End底部壁厚End Wall Thickness外径Outside Diameter 螺纹长度Length of Thread MinE F C min DDN NPS SCH160、XXS3000、6000SCH1603000XXS6000SCH1603000XXS6000SCH1603000XXS6000B L26 8 10 1/81/43/8323538192525---27274.84.84.8---6.46.41619222225326.48.19.16.710.210.415 20 25 1/23/414851603237413338436.46.49.77.97.911.228354438445710.912.714.713.613.917.332 40 50 11/411/226779864444484648519.711.212.711.212.715.757647664769217.017.819.018.018.419.265 80 100 21/2349210812160656864687515.719.022.419.022.428.49210814010812715923.625.927.728.930.533.0螺纹管件Threaded Fittings GB/T 1426、ASME B16.11公称通径Nominal Pipe Size长度Length方头管塞Square Head Plugs圆头管塞Round Head Plugs六角头管塞和内外螺纹接头Hex Plugs and Bushings方头高度Height of Square对边宽度Width Flats头部直径NominalDiameter ofHead长度Length对边宽度Width Flats(Nominal)六角头高度Hex HeighDN NPS L2 min B min C min D L min S K min H min6 8 10 1/81/43/810111366871011101418354141111618---3466815 20 25 1/23/411416191011131416212127334444512227365668101032 40 50 11/411/2221212214161824283243486051516446506578914161865 80 100 21/23427283219212536416573891447070767590115101013192125螺比试管件中的螺纹型式为GB/T 12716(ANSI/ASME B1.20.1)中的60°圆锥管螺纹NPT；如采用其它型式的螺纹请在订货时注明。