Router8后处理器的设置方法1：安装好Router8后，在C盘找到Router8文件夹，进入exe文件夹,右键选取发送到桌面快捷方式，然后双击图标，后显示加入机器对话框如下图（1-1），（或进入软件界面后，点击上方中间操作机器，然后选取机器设定）上图（1-1）2：单击加入机器选择所有机器类型中的ISO TYPE CRRTESIAN XYZ后点击加入如下图（2-2）上图（2-2）3:点击机器设置中的后处理器如下图（3-3）上图（3-3）4：在机器设置的滚动条空白处单击两下将Nmax=9999改为Nmax=99999999如下图（4-4）修改前上图（4-4-1）5：点击下滚动条将HeadPcrSz0=%p改为HeadPcrSz0=O1（大写欧1），将HeadPcrSz1=(AXE XYZ)，HeadPcrSz2=t M6，等号后的值删除。
如下图（5-5）修改前上图（5-5-1）6：点击下滚动条将EndPcrNb=2改为EndPcrNb=3，将EndPcrSz0=M2改为EndPcrSz0=M05,将EndPcrSz1=p0改为EndPcrSz1=M30,将EndPcrSz2=改为EndPcrSz2=%如下图(6-6)。
修改完成后点击确认，然后保存。
修改前上图(6-6-1)7：将设置机器总尺寸最小(X,Y,Z),最大（X，Y，Z）中的值后面加上3-4个零, 名称中可设置成相应的机器类型后点击确定后退出修改前图（7-7-1）8:确认退出保存后，会自动进入Router8界面，然后点击右上角编辑、进入选项上图8-1进入选项后，把通用中数值，改为如图8-2加黑框处数据：通用上图8-2修改可雕刻页中数值，如图8-3加黑框处。
（图中数据只作为参照，修改时请按照当前使用机床的型号和加工行程修改）可雕刻页上图8-3把通用计算参数中设置，改为如图8-4加黑框处设置通用计算参数上图8-4把特别计算参数中设置，改为如图8-5加黑框处设置特别计算参数上图8-5以上修改完成后，点击确定保存设置。
9：任意画一个图形，进入雕刻加工页面（CAM模块），选取图形任意计算一个路径，然后进入机器工作界面，如图9-1黑框处进入机器工作界面后，按照如图9-2加黑框处设置上图9-2设置完成后，点击右上角份额，进入份额界面如图9-3-1，然后按照入图9-3-2加黑框处设置上图9-3-1上图9-3-2以上操作完成后，点击确认，退出份额界面，在机器工作界面，点击确认，然后点击执行，后处理器设置完成。
如图9-4上图9-4Router8 post processor setting method1: After installing Router8, find the Router8 folder on the C drive, enter the exe folder, right-click to send the shortcut to the desktop, and then double-click the icon, then display the dialog box for joining the machine as shown below (1-1), (or enter the software After the interface, click on the upper middle to operate the machine, then select the machine settings)Above (1-1)2: Click Join Machine to select ISO TYPE CRRTESIAN XYZ in all machine types and click to add as shown below (2-2)Above (2-2)3: Click on the post processor in the machine settings as shown below (3-3)Above (3-3)4: Click twice in the blank space of the scroll bar set by the machine to change Nmax=9999 to Nmax=99999999 as shown below (4-4)Before modification, above (4-4-1)After modification, the above picture (4-4-2)5: Click the scroll bar to change HeadPcrSz0=%p to HeadPcrSz0=O1 (uppercased Euro 1), and remove HeadPcrSz1=(AXE XYZ), HeadPcrSz2=t M6, and the value after the equal sign. As shown below (5-5)Before modification (5-5-1)After modification, the above picture (5-5-2)6: Click the scroll bar to change EndPcrNb=2 to EndPcrNb=3, EndPcrSz0=M2 toEndPcrSz0=M05, EndPcrSz1=p0 to EndPcrSz1=M30, EndPcrSz2= to EndPcrSz2=% as shown below (6-6 ). Click OK when the modification is complete, then save.Before modification (6-6-1)After modification, the above picture (6-6-2)7: Set the total machine size to the minimum (X, Y, Z), and add 3-4 zeros to the value in the maximum (X, Y, Z).Name can be set to the corresponding machine type, click OK to exitBefore modification (7-7-1)Modified Figure (7-7-2)8: After confirming to exit the save, it will automatically enter the Router8 interface, then click onthe upper right corner to edit and enter the option.Figure 8-1 aboveAfter entering the option, change the value in the common to the data in the black box as shown in Figure 8-2:General purposeFigure 8-2 aboveModify the value in the engratable page, as shown in Figure 8-3. (The data in the figure is only for reference. Please modify it according to the model and processing stroke of the current machine tool.)Engravable pageFigure 8-3 aboveSet the general calculation parameters to be changed to the black box as shown in Figure 8-4.General calculation parametersFigure 8-4 aboveSet the special calculation parameters to be changed as shown in Figure 8-5 and black box.Special calculation parametersFigure 8-5 aboveAfter the above changes are completed, click OK to save the settings.9: Arbitrarily draw a graphic, enter the engraving processing page (CAM module), select the graphic to calculate a path arbitrarily, and then enter the machine working interface, as shown in Figure 9-1.Figure 9-1 aboveAfter entering the machine working interface, set it as black as shown in Figure 9-2.Figure 9-2 aboveAfter the setting is completed, click the share in the upper right corner, enter the share interface as shown in Figure 9-3-1, and then set it in the black box according to Figure 9-3-2.Figure 9-3-1 aboveFigure 9-3-2 aboveAfter the above operation is completed, click Confirm to exit the share interface. In the machine work interface, click Confirm, then click Execute, and the post processor setting is completed. As shown in Figure 9-4Figure 9-4 above。