FEATURESDCT OR DCU PACKAGE(TOP VIEW)1B1827V CCB 36OE 45B2GND V CCA A2A1YZP PACKAGE (BOTTOM VIEW)A254A136OE V CCA 27V CCBGND8B11B2A1B1C1D1A2B2C2D2DESCRIPTION/ORDERINGINFORMATIONTXS0102 SCES640A–JANUARY 2007–REVISED MAY 20082-BIT BIDIRECTIONAL VOLTAGE-LEVEL TRANSLATOR FOR OPEN-DRAIN AND PUSH-PULL APPLICATIONS•No Direction-Control Signal Needed •ESD Protection Exceeds JESD 22•Max Data Rates–A Port–24Mbps (Push Pull)–2500-V Human-Body Model (A114-B)–2Mbps (Open Drain)–250-V Machine Model (A115-A)•Available in the Texas Instruments NanoFree™–1500-V Charged-Device Model (C101)Package–B Port• 1.65V to 3.6V on A port and 2.3V to 5.5V on –8-kV Human-Body Model (A114-B)B port (V CCA ≤V CCB )–250-V Machine Model (A115-A)•V CC Isolation Feature –If Either V CC Input Is at –1500-V Charged-Device Model (C101)GND,Both Ports Are in the High-Impedance State•No Power-Supply Sequencing Required –Either V CCA or V CCB Can Be Ramped First •I off Supports Partial-Power-Down Mode Operation•Latch-Up Performance Exceeds 100mA Per JESD 78,Class IIThis two-bit noninverting translator uses two separate configurable power-supply rails.The A port is designed to track V CCA .V CCA accepts any supply voltage from 1.65V to 3.6V.The B port is designed to track V CCB .V CCA must be less than or equal to V CCB .V CCB accepts any supply voltage from 2.3V to 5.5V.This allows for low-voltage bidirectional translation between any of the 1.8-V,2.5-V,3.3-V,and 5-V voltage nodes.When the output-enable (OE)input is low,all outputs are placed in the high-impedance state.To ensure the high-impedance state during power up or power down,OE should be tied to GND through a pulldown resistor;the minimum value of the resistor is determined by the current-sourcing capability of the driver.ORDERING INFORMATIONT APACKAGE (1)(2)ORDERABLE PART NUMBER TOP-SIDE MARKING (3)NanoStar™–WCSP (DSBGA)Reel of 3000TXS0102YZPR 2H_0.23-mm Large Bump –YZPReel of 3000TXS0102DCTR NFEZ___–40°C to 85°CSSOP –DCT Tube of 250TXS0102DCTT NFEZ ___VSSOP –DCUReel of 3000TXS0102DCURNFE_(1)Package drawings,thermal data,and symbolization are available at /packaging .(2)For the most current package and ordering information,see the Package Option Addendum at the end of this document,or see the TI website at .(3)DCT:The actual top-side marking has three additional characters that designate the year,month,and assembly/test site.DCU:The actual top-side marking has one additional character that designates the assembly/test site.YZP:The actual top-side marking has three preceding characters to denote year,month,and sequence code,and one following character to designate the assembly/test site.Pin 1identifier indicates solder-bump composition (1=SnPb,•=Pb-free).Please be aware that an important notice concerning availability,standard warranty,and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.NanoFree is a trademark of Texas Instruments.PRODUCTION DATA information is current as of publication date.Copyright ©2007–2008,Texas Instruments IncorporatedProducts conform to specifications per the terms of the Texas Instruments standard warranty.Production processing does not necessarily include testing of all parameters.3.3 V1.8 VTXS0102SCES640A–JANUARY2007–REVISED PIN DESCRIPTION(DCT AND DCU PACKAGES) FUNCTION1B2Input/output B.Referenced to V CCB.2GND Ground3V CCA A-port supply voltage.1.65V≤V CCA≤3.6V and V CCA≤V CCB4A2Input/output A.Referenced to V CCA.5A1Input/output A.Referenced to V CCA.3-state output mode enable.Pull OE low to place all outputs in3-state mode.6OEReferenced to V CCA.7V CCB B-port supply voltage.2.3V≤V CCB≤5.5V8B1Input/output B.Referenced to V CCB.TYPICAL OPERATING CIRCUIT2Submit Documentation Feedback Copyright©2007–2008,Texas Instruments IncorporatedProduct Folder Link(s):TXS0102ABSOLUTE MAXIMUM RATINGS (1)RECOMMENDED OPERATING CONDITIONS (1)(2)TXS0102 SCES640A–JANUARY 2007–REVISED MAY 2008over recommended operating free-air temperature range (unless otherwise noted)MINMAX UNIT V CCA Supply voltage range –0.5 4.6V V CCB Supply voltage range –0.5 6.5V A port –0.5 4.6V I Input voltage range (2)V B port –0.5 6.5A port –0.5 4.6Voltage range applied to any outputV O V in the high-impedance or power-off state (2)B port –0.5 6.5A port –0.5V CCA +0.5V O Voltage range applied to any output in the high or low state (2)(3)VB port –0.5V CCB +0.5I IK Input clamp current V I <0–50mA I OK Output clamp current V O <0–50mA I OContinuous output current±50mA Continuous current through V CCA ,V CCB ,or GND±100mADCT package220θJA Package thermal impedance (4)DCU package 227°C/W YZP package102T stg Storage temperature range–65150°C (1)Stresses beyond those listed under "absolute maximum ratings"may cause permanent damage to the device.These are stress ratings only,and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions"is not implied.Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.(2)The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.(3)The value of V CCA and V CCB are provided in the recommended operating conditions table.(4)The package thermal impedance is calculated in accordance with JESD 51-7.V CCAV CCBMIN MAX UNIT V CCA 1.65 3.6Supply Vvoltage (3)V CCB2.35.51.65V to 1.95V V CCI –0.2V CCI A-port I/Os2.3V to 5.5V 2.3V to3.6V V CCI –0.4V CCI High-level V IHV input voltageB-port I/Os V CCI –0.4V CCI 1.65V to 3.6V2.3V to 5.5VOE input V CCA ×0.655.5A-port I/Os00.15Low-level V ILB-port I/Os 1.65V to 3.6V2.3V to 5.5V00.15V input voltageOE inputV CCA ×0.35A-port I/Os,push-pull driving10Input transitionΔt/Δv B-port I/Os,push-pull driving1.65V to 3.6V2.3V to 5.5V10ns/V rise or fall rateControl input 10T A Operating free-air temperature–4085°C (1)V CCI is the supply voltage associated with the input port.(2)V CCO is the supply voltage associated with the output port.(3)V CCA must be less than or equal to V CCB ,and V CCA must not exceed 3.6V.Copyright ©2007–2008,Texas Instruments Incorporated Submit Documentation Feedback3Product Folder Link(s):TXS0102ELECTRICAL CHARACTERISTICS (1)(2)(3)TXS0102SCES640A–JANUARY 2007–REVISED MAY over recommended operating free-air temperature range (unless otherwise noted)T A =25°C –40°C to 85°CTEST PARAMETER V CCA V CCB UNIT CONDITIONS MINTYP MAXMIN MAXI OH =–20µA,V OHA 1.65V to 3.6V 2.3V to 5.5V V CCA ×0.67V V IB ≥V CCB –0.4V I OL =1mA,V OLA 1.65V to 3.6V 2.3V to 5.5V 0.4V V IB ≤0.15V I OH =–20µA,V OHB 1.65V to 3.6V 2.3V to 5.5V V CCB ×0.67V V IA ≥V CCA –0.2V I OL =1mA,V OLB 1.65V to 3.6V 2.3V to 5.5V 0.4V V IA ≤0.15VI I OE 1.65V to 3.6V2.3V to 5.5V ±1±2µA A port 0V 0to 5.5V ±1±2µA I off B port 0to3.6V 0V ±1±2µA I OZ A or B port1.65V to 3.6V2.3V to 5.5V ±1±2µA1.65V to V CCB2.3V to 5.5V2.4V I =V O =open,I CCA3.6V 0V 2.2µAI O =00V 5.5V –11.65V to V CCB2.3V to 5.5V12V I =V O =open,I CCB3.6V 0V –1µA I O =00V 5.5V 1V I =V CCI or GND,I CCA +I CCB 1.65V to V CCB2.3V to 5.5V14.4µA I O =0C I OE 3.3V 3.3V 2.5 3.5pF A or B port 3.3V3.3V10C ioA port 56pFB port67.5(1)V CCI is the V CC associated with the input port.(2)V CCO is the V CC associated with the output port.(3)V CCA must be less than or equal to V CCB ,and V CCA must not exceed 3.6V.4Submit Documentation FeedbackCopyright ©2007–2008,Texas Instruments IncorporatedProduct Folder Link(s):TXS0102TIMING REQUIREMENTS TIMING REQUIREMENTS TIMING REQUIREMENTS TXS0102 SCES640A–JANUARY2007–REVISED MAY2008over recommended operating free-air temperature range,V CCA=1.8V±0.15V(unless otherwise noted)V CCB=2.5V V CC=3.3V V CC=5V±0.2V±0.3V±0.5V UNITMIN MAX MIN MAX MIN MAXPush-pull driving212224 Data rate Mbp Open-drain driving222t w Push-pull driving474541 PulseData inputs ns duration Open-drain driving500500500over recommended operating free-air temperature range,V CCA=2.5V±0.2V(unless otherwise noted)V CCB=2.5V V CC=3.3V V CC=5V±0.2V±0.3V±0.5V UNITMIN MAX MIN MAX MIN MAXPush-pull driving202224 Data rate Mbp Open-drain driving222t w Push-pull driving504541 PulseData inputs ns duration Open-drain driving500500500over recommended operating free-air temperature range,V CCA=3.3V±0.3V(unless otherwise noted)V CC=3.3V V CC=5V±0.3V±0.5V UNITMIN MAX MIN MAXPush-pull driving2324 Data rate Mbps Open-drain driving22t w Push-pull driving4341 Pulse duration Data inputs ns Open-drain driving500500Copyright©2007–2008,Texas Instruments Incorporated Submit Documentation Feedback5Product Folder Link(s):TXS0102SWITCHING CHARACTERISTICSTXS0102SCES640A–JANUARY 2007–REVISED MAY over recommended operating free-air temperature range,V CCA =1.8V ±0.15V (unless otherwise noted)V CCB =2.5V V CCB =3.3V CCB =5V ±0.2V V FROM TO TEST ±0.5V PARAMETERUNIT±0.3V (INPUT)(OUTPUT)CONDITIONSMIN MAXMIN MAXMIN MAXPush-pull driving5.3 5.46.8t PHLOpen-drain driving 2.38.8 2.49.6 2.610ABns Push-pull driving 6.87.17.5t PLH Open-drain driving 452603*********Push-pull driving 4.4 4.5 4.7t PHLOpen-drain driving 1.9 5.3 1.1 4.4 1.24BA ns Push-pull driving 5.3 4.50.5t PLH Open-drain driving451753614027102t en OE A or B 200200200ns t dis OEA or B504035ns Push-pull driving 3.29.5 2.39.327.6t rA A-port rise time ns Open-drain driving 38165301322295Push-pull driving 410.8 2.79.1 2.77.6t rB B-port rise time ns Open-drain driving 34145231061058Push-pull driving 2 5.9 1.96 1.713.3t fA A-port fall time Open-drain driving 4.4 6.9 4.3 6.4 4.2 6.1ns Push-pull driving 2.913.8 2.816.2 2.816.2t fB B-port fall time Open-drain driving 6.913.87.516.2716.2t SK(O)Channel-to-channel skew0.70.70.7ns Push-pull driving 212224Max data rateMbps Open-drain driving2226Submit Documentation FeedbackCopyright ©2007–2008,Texas Instruments IncorporatedProduct Folder Link(s):TXS0102SWITCHING CHARACTERISTICS TXS0102 SCES640A–JANUARY2007–REVISED MAY2008over recommended operating free-air temperature range,V CCA=2.5V±0.2V(unless otherwise noted)V CCB=2.5V CCB=3.3V V CCB=5VVFROM TO TEST±0.3V±0.5V PARAMETER UNIT±0.2V(INPUT)(OUTPUT)CONDITIONSMIN MAX MIN MAX MIN MAXPush-pull driving 3.2 3.7 3.8 t PHLOpen-drain driving 1.7 6.326 2.1 5.8A B nsPush-pull driving 3.5 4.1 4.4 t PLHOpen-drain driving432503*********Push-pull driving3 3.6 4.3 t PHLOpen-drain driving 1.8 4.7 2.6 4.2 1.24B A nsPush-pull driving 2.5 1.61 t PLHOpen-drain driving441703714027103 t en OE A or B200200200ns t dis OE A or B504035nsPush-pull driving 2.87.4 2.6 6.6 1.8 5.6 t rA A-port rise time nsOpen-drain driving34149281212489Push-pull driving 3.28.3 2.97.2 2.4 6.1 t rB B-port rise time nsOpen-drain driving35151241121264Push-pull driving 1.9 5.7 1.9 5.5 1.8 5.3 t fA A-port fall time nsOpen-drain driving 4.4 6.9 4.3 6.2 4.2 5.8Push-pull driving 2.27.8 2.4 6.7 2.6 6.6 t fB B-port fall time nsOpen-drain driving 5.18.8 5.49.4 5.410.4 t SK(O)Channel-to-channel skew0.70.70.7nsPush-pull driving202224Max data rate MbpsOpen-drain driving222Copyright©2007–2008,Texas Instruments Incorporated Submit Documentation Feedback7Product Folder Link(s):TXS0102SWITCHING CHARACTERISTICSTXS0102SCES640A–JANUARY 2007–REVISED MAY over recommended operating free-air temperature range,V CCA =3.3V ±0.3V (unless otherwise noted)V CCB =3.3V V CCB =5V FROM TO TEST ±0.3V ±0.5V PARAMETERUNIT(INPUT)(OUTPUT)CONDITIONSMINMAX MIN MAXPush-pull driving2.43.1t PHLOpen-drain driving 1.3 4.2 1.4 4.6ABns Push-pull driving 4.2 4.4t PLH Open-drain driving 3620428165Push-pull driving 2.5 3.3t PHLOpen-drain driving 1124197BA ns Push-pull driving 2.5 2.6t PLH Open-drain driving31393105t en OE A or B 200200ns t dis OEA or B4035ns Push-pull driving 2.3 5.6 1.9 4.8t rA A-port rise time ns Open-drain driving 251161985Push-pull driving 2.5 6.4 2.17.4t rB B-port rise time ns Open-drain driving 261161472Push-pull driving 2 5.4 1.95t fA A-port fall time ns Open-drain driving 4.3 6.1 4.2 5.7Push-pull driving 2.37.4 2.47.6t fB B-port fall time ns Open-drain driving57.6 4.88.3t SK(O)Channel-to-channel skew0.70.7ns Push-pull driving 2324Max data rateMbps Open-drain driving228Submit Documentation FeedbackCopyright ©2007–2008,Texas Instruments IncorporatedProduct Folder Link(s):TXS0102PRINCIPLES OF OPERATIONApplicationsArchitectureV CCA V CCBInput Driver RequirementsPower UpEnable and DisableTXS0102 SCES640A–JANUARY 2007–REVISED MAY 2008The TXS0102can be used in level-translation applications for interfacing devices or systems operating at different interface voltages with one another.The TXS0102is ideal for use in applications where an open-drain driver is connected to the data I/Os.The TXS0102can also be used in applications where a push-pull driver is connected to the data I/Os,but the TXB0102might be a better option for such push-pull applications.The TXS0102architecture (see Figure 1)does not require a direction-control signal to control the direction of data flow from A to B or from B to A.Figure 1.Architecture of a TXS01xx CellEach A-port I/O has an internal 10-k Ωpullup resistor to V CCA ,and each B-port I/O has an internal 10-k Ωpullup resistor to V CCB .The output one-shots detect rising edges on the A or B ports.During a rising edge,the one-shot turns on the PMOS transistors (T1,T2)for a short duration,which speeds up the low-to-high transition.The fall time (t fA ,t fB )of a signal depends on the output impedance of the external device driving the data I/Os of the TXS0102.Similarly,the t PHL and max data rates also depend on the output impedance of the external driver.The values for t fA ,t fB ,t PHL ,and maximum data rates in the data sheet assume that the output impedance of the external driver is less than 50Ω.During operation,ensure that V CCA ≤V CCB at all times.During power-up sequencing,V CCA ≥V CCB does not damage the device,so any power supply can be ramped up first.The TXS0102has an OE input that is used to disable the device by setting OE low,which places all I/Os in the Hi-Z state.The disable time (t dis )indicates the delay between the time when OE goes low and when the outputs actually get disabled (Hi-Z).The enable time (t en )indicates the amount of time the user must allow for the one-shot circuitry to become operational after OE is taken high.Copyright ©2007–2008,Texas Instruments Incorporated Submit Documentation Feedback9Product Folder Link(s):TXS0102TXS0102SCES640A–JANUARY2007–REVISED Pullup or Pulldown Resistors on I/O LinesEach A-port I/O has an internal10-kΩpullup resistor to V CCA,and each B-port I/O has an internal10-kΩpullup resistor to V CCB.If a smaller value of pullup resistor is required,an external resistor must be added from the I/O to V CCA or V CCB(in parallel with the internal10-kΩresistors).10Submit Documentation Feedback Copyright©2007–2008,Texas Instruments IncorporatedProduct Folder Link(s):TXS0102PARAMETER MEASUREMENT INFORMATIONV OH V OLOutput Control (low-level enabling)Output Waveform 1S1 at 2 × V CCO (see Note B)Output Waveform 2S1 at GND (see Note B)0 V0 V V CCI0 VV CCA V CCO VOLTAGE WAVEFORMSPROPAGATION DELAY TIMES VOLTAGE WAVEFORMSPULSE DURATION VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMESInput A.C L includes probe and jig capacitance.B.Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.C.All input pulses are supplied by generators having the following characteristics: PRR v 10 MHz, Z O = 50 Ω, dv/dt ≥ 1 V/ns.D.The outputs are measured one at a time, with one transition per measurement.E.t PLZ and t PHZ are the same as t dis .F.t PZL and t PZH are the same as t en .G.t PLH and t PHL are the same as t pd .H.V CCI is the V CC associated with the input port.I.V CCO is the V CC associated with the output port.J.All parameters and waveforms are not applicable to all devices.W DATA RATE, PULSE DURATION, PROPAGATION DELAY ,OUTPUT RISE AND FALL TIME MEASUREMENT USINGA PUSH-PULL DRIVER W DATA RATE, PULSE DURATION, PROPAGATION DELAY ,OUTPUT RISE AND FALL TIME MEASUREMENT USING AN OPEN-DRAIN DRIVERTXS0102 SCES640A–JANUARY 2007–REVISED MAY 2008Figure 2.Load Circuit and Voltage WaveformsPACKAGING INFORMATIONOrderable Device Status(1)PackageType PackageDrawingPins PackageQtyEco Plan(2)Lead/Ball Finish MSL Peak Temp(3)TXS0102DCTR ACTIVE SM8DCT83000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMTXS0102DCTRE4ACTIVE SM8DCT83000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMTXS0102DCTT ACTIVE SM8DCT8250Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMTXS0102DCTTE4ACTIVE SM8DCT8250Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMTXS0102DCTTG4ACTIVE SM8DCT8250Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMTXS0102DCUR ACTIVE US8DCU83000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMTXS0102DCURG4ACTIVE US8DCU83000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMTXS0102DCUT ACTIVE US8DCU8250Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMTXS0102DCUTG4ACTIVE US8DCU8250Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMTXS0102YZPR ACTIVE DSBGA YZP83000Green(RoHS&no Sb/Br)SNAGCU Level-1-260C-UNLIMTXS0102YZTR ACTIVE DSBGA YZT83000Green(RoHS&no Sb/Br)SNAGCU Level-1-260C-UNLIM(1)The marketing status values are defined as follows:ACTIVE:Product device recommended for new designs.LIFEBUY:TI has announced that the device will be discontinued,and a lifetime-buy period is in effect.NRND:Not recommended for new designs.Device is in production to support existing customers,but TI does not recommend using this part in a new design.PREVIEW:Device has been announced but is not in production.Samples may or may not be available.OBSOLETE:TI has discontinued the production of the device.(2)Eco Plan-The planned eco-friendly classification:Pb-Free(RoHS),Pb-Free(RoHS Exempt),or Green(RoHS&no Sb/Br)-please check /productcontent for the latest availability information and additional product content details.TBD:The Pb-Free/Green conversion plan has not been defined.Pb-Free(RoHS):TI's terms"Lead-Free"or"Pb-Free"mean semiconductor products that are compatible with the current RoHS requirements for all6substances,including the requirement that lead not exceed0.1%by weight in homogeneous materials.Where designed to be soldered at high temperatures,TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free(RoHS Exempt):This component has a RoHS exemption for either1)lead-based flip-chip solder bumps used between the die and package,or2)lead-based die adhesive used between the die and leadframe.The component is otherwise considered Pb-Free(RoHS compatible)as defined above.Green(RoHS&no Sb/Br):TI defines"Green"to mean Pb-Free(RoHS compatible),and free of Bromine(Br)and Antimony(Sb)based flame retardants(Br or Sb do not exceed0.1%by weight in homogeneous material)(3)MSL,Peak Temp.--The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications,and peak solder temperature.Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided.TI bases its knowledge and belief on information provided by third parties,and makes no representation or warranty as to the accuracy of such information.Efforts are underway to better integrate information from third parties.TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary,and thus CAS numbers and other limited information may not be available for release.In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s)at issue in this document sold by TIto Customer on an annual basis.TAPE AND REEL INFORMATION*All dimensions are nominal Device Package Type Package DrawingPinsSPQ Reel Diameter (mm)Reel Width W1(mm)A0(mm)B0(mm)K0(mm)P1(mm)W (mm)Pin1Quadrant TXS0102DCUR US8DCU 83000180.09.2 2.25 3.35 1.05 4.08.0Q3TXS0102YZPR DSBGAYZP 83000180.08.4 1.1 2.10.56 4.08.0Q1TXS0102YZTR DSBGA YZT 83000180.08.4 1.02 2.020.754.08.0Q1*All dimensions are nominalDevice Package Type Package Drawing Pins SPQ Length(mm)Width(mm)Height(mm) TXS0102DCUR US8DCU83000202.0201.028.0 TXS0102YZPR DSBGA YZP83000220.0220.034.0 TXS0102YZTR DSBGA YZT83000220.0220.034.0MECHANICAL DATAMPDS049B – MAY 1999 – REVISED OCTOBER 2002DCT (R-PDSO-G8)PLASTIC SMALL-OUTLINE PACKAGE 0,600,200,250°– 8°0,15 NOMGage Plane4188781/C 09/024,2550,300,152,903,752,70843,152,7510,100,001,30 MAX Seating Plane0,10M 0,130,65PIN 1INDEX AREANOTES: A.All linear dimensions are in millimeters.B.This drawing is subject to change without notice.C.Body dimensions do not include mold flash or protrusion D.Falls within JEDEC MO-187 variation DA.IMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements,improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right, or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered rmation of third parties may be subject to additional restrictions.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use any non-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers AudioData Converters AutomotiveDSP BroadbandClocks and Timers Digital ControlInterface MedicalLogic MilitaryPower Mgmt Optical NetworkingMicrocontrollers SecurityRFID TelephonyRF/IF and ZigBee®Solutions Video&ImagingWirelessMailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265Copyright©2008,Texas Instruments Incorporated。