设备说明书EQUIPMENT MANUAL ITC-M-4-700全自动抛光机AUTOMATIC POLISHING MACHINE内容概要CATALOGUE一、设备特点及描述EQUIPMENT FEATURE AND DESCRIPTION二、设备安装EQUIPMENT INSTALLATION三、设备操作及参数调用EQUIPMENT OPERATION AND PARAMETER USING四、参数设定与修改PARAMETER WRITE AND CHANGE五、设备维护及保养EQUIPMENT MAINTENANCE六、安全操作等其它事项OPERATION SAFTLY AND OTHERS一、设备特点及描述EQUIPMENT FEATURE AND DESCRIPTION布轮直径WHEEL DIAMETER400–800mm工位车轴直径STATION AXLE DIAMETER70mm布轮可变转速WHEEL SPEED100-2400rpm装机功率INSTALLED POWER40KW电源电压POWER SUPPLY VOLTAGE380V.+N+PE排尘口直径DUST OUTLET DIAMETER2×200mm转台轴可变转速TRUNTABLE AXIS VARIABLE SPEED1–25rpm 通过过滤器处理的干净气源CLEAN GAS SOURCE THROUGH THE FILTER >0.6Mpa工件高度WORKERPIECE HIGHT150mm前后行程FORWARD AND BACKWARD0-380mm左右行程LEFTWARD AND RIGHTWARD0-280mm设备尺寸DIAMENSION OF THE EQUIPMENT4240×2110×2115mm 设备重量WEIGHT OF THE EQUIPMENT5000KG该设备专为自动抛光而设计，并使用一项新技术对物体进行抛光。
特别是在对不规则物体某一部分进行抛光时，可以在不损害整体的情况下整齐平滑地完成任务。
采用双组操作程序，同时可以精抛两种不同的工件，设备可以自动切换。
同时也采用了角度精抛程序，通过编程，设定精抛角度，对工件复杂的部位可以加强精抛的力度。
布轮的直径大设计灵活，可以在仅旋转数圈的情况下就能达到较高的速度。
物体的固定通过设备夹钳进行控制。
该设备是由两边抛光布轮，一个带有4个工位车轴的旋转工作台组成，可以一次性抛光出两件成品。
The device is designed for automatic polishing,and using a new technique for polishing the object,especially in certain parts of irregular objects polishing.Under the condition of without make damage to the whole part,itcan polish smoothly and tidily.Dual group procedures,and can polish two different parts at the same time,the device can automatically switch.It also adopted the point of precision polishing process,by programming,setting fine polishing angle of the work piece of complex parts can strengthen the polish.The wheel diameter designed to be flexible,you can only spin a few laps in the case will be able to reach a higher speed.The device make fixture by clamp.The device have polishing wheel on either side,with a four-station rotary table axle components,you can polish two products at the same time.二、设备安装EQUIPMENT INSTALLATION1、客户接收到设备后，要检查其是否由于运输而受损，或者设备缺少部件和相应的更换布轮的特殊扳手。
如发现以上两种情况中的任意一种，应尽早通知相关负责人。
After the customer receives the equipment,he or she should check whether there is any damage,missing parts or equipment replacement cloth wheel and the corresponding special wrench during the transport.If any one of them happen,he or she should notify the responsible person.2、对设备的挪动，可以用起重机（如图1）或叉车。
设备必须放置在平地上，混凝土地面最好，把设备配的四个垫铁安上，调整设备的水平位置。
Moving the equipment can use crane(Figure1)or forklift.Equipment must be placed on level ground,preferably concrete floor.The placement of the device with four horns,adjust the horizontal position of the device.图13、设备供气总进气源必须有经过过滤器处理后的干净气源，通过调压三联件把气压设定在≥0.6MPa。
The total inlet gas source of equipment must be processed through the filter clean air source,through the pressure regulator set at FRL≥0.6MPa.4、装好喷蜡系统即先把喷蜡罐出蜡的螺纹口与设备的进蜡螺纹口衔接紧固，再把喷蜡罐上面的气源接好，把压力调在0.2-0.3MPa。
Install the paste supply system is link spray cans of wax in the threads and screw the device into the mouth of convergence fastening wax at first.Then the gas tank above the source connected,adjust the pressure in the0.2-0.3MPa.5、检查电压是否如控制面板上所示：z 连接配电柜的是3*25mm，电压为380V 的电缆，同接地线共同使用。
将其与所示连接字母R，S，T+N 接点及地面相连接。
z 特别要注意的是保证地线连接到相应的接线端子上。
抛光布轮的升降方向如果相反话，可以交换一下端子R 和S 的连接。
z设备配电箱必须保持关闭状态，以避免灰尘，液体或其他异物进入内部。
z 随机附带保养或维修的电路图。
注：此设备不带差速保护，连接线有必要带此差速保护装置。
Check whether the voltage on the control panel as follows:Connect with power distribution cabinet of 3*25mm,380V cable with ground wire use.It will be connected with the letters R,S,T +N and ground contactor.Particularly pay attention to ensure the ground wire to the corresponding terminals.If polishing wheel goes to the opposite direction,you can change the connection terminals R and S.Equipment power distribution carbine must remain closed to prevent dust,liquid or other thing goes into the interior.Maintenance and repair circuit will along with the machine.Note:The machine have no speed variation protection,cable is necessary to take this variation protection device.6、按照上面各部分的注解，给设备通电，并连接除尘系统装置。
Power the equipment and connect the dust clean system according to the explanationabove.7、如有任何安装方面的问题，请联系厂家。
电话：+86-137********，邮箱：***********************，咨询QQ：827971807.If you have any problem of installation,please contact our factory.TEL:+86-137********,Email:***********************.三、设备操作及参数调用EQUIPMENT OPERATION AND PARAMETER USING1、通上气源，接上电源，再用程序钥匙打开触摸屏，开启控制电源进入主菜单界面。
如安全重置按钮灯亮则需按下安全重置按钮才可以进行下步。
如图：Connect to the gas source and the power supply.Then use the program key to open the touch screen,turn on the control power and enter the main menu.If the security reset lights on,you need to press the reset button.Thus it can move on to the next step.Figure:2、在手动情况下：点击主菜单“手动调试”，然后点击手动调试中的“参数设置”。