FI22FP
Diffuse Mode
with PBT66U Fiber
PBT66U
2.40 in 1.60 in 0.80 in 0 0.80 in 1.60 in 2.40 in
0 25 mm 50 mm 75 mm 100 mm 125 mm 1.0 in 2.0 in 3.0 in 4.0 in 5.0 in
DISTANCE
1000
E X C E 100 S S
G 10 A I N
1 0.1 mm .004 in
FI22
Diffuse Mode
with PBT26U Fiber
PBT26U
1 mm .04 in
10 mm 0.4 in
DISTANCE
100 mm 4 in
6 mm 4 mm 2 mm
0 2 mm 4 mm 6 mm
Programming Push Buttons SETUP Status
Indicators: Light Operate Dark Operate
Delay Switching
Point
Bargraph Display
Figure 1. FI22FP features
Sensing Beam Supply Voltage Supply Protection Circuitry Delay at Power Up Output Configuration
FI22FP Series
Low-Profile, Inline Plastic Fiber Optic Sensor
FI22FP Inline Fiber Optic Sensor Features
• Low-profile fiber optic sensors are designed for inconspicuous surface mounting • 8-segment LED light bar indicates relative received signal strength, sensing
60 mm 40 mm 20 mm
0 20 mm 40 mm 60 mm
FI22FP
Opposed Mode
with PIT46U Fiber
PIT46U
2.40 in 1.60 in 0.80 in 0 0.80 in 1.60 in 2.40 in
150 mm 100 mm 50 mm
0 50 mm 100 mm 150 mm
This product does NOT include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.
0 20 mm 40 mm 60 mm
FI22FP
Diffuse Mode
with PBT46U Fiber
PBT46U
2.40 in 1.60 in 0.80 in 0 0.80 in 1.60 in 2.40 in
0 25 mm 50 mm 75 mm 100 mm 125 mm 1.0 in 2.0 in 3.0 in 4.0 in 5.0 in
** See page 2 for beam patterns and excess gain curves.
!
WARNING . . . Not To Be Used for Personnel Protection
Never use this product as a sensing device for personnel protection. Doing so could lead to serious injury or death.
Maximum Range**
Range varies depending on sensing mode and fiber optic(s) used; see below and page 2 for typical values.
10 to
Bipolar
30V dc NPN/PNP
Opposed Mode PIT26U Fiber: 60 mm (2.36") PIT46U Fiber: 260 mm (10.24") PIT66U Fiber: 540 mm (21.26")
FI22FP
Opposed Mode
with PIT66U Fiber
PIT66U
6.0 in 4.0 in 2.0 in 0 2.0 in 4.0 in 6.0 in
0 15 mm 30 mm 45 mm 60 mm 75 mm 0.60 in 1.20 in 1.80 in 2.40 in 3.00 in
Output Rating
Output Protection Output Response Time Repeatability
Adjustments
Indicators
Construction Environmental Rating Connections Operating Conditions
Fiber Ports
Green Power ON Indicator
Yellow Output Conducting Indicator
FI22FPQ
Integral 6-pin Pico-style QD
Diffuse Mode PBT26U Fiber: 60 mm (2.36") PBT46U Fiber: 60 mm (2.36") PBT66U Fiber: 60 mm (2.36")
*9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., FI22FP W/30). A model with a QD connector requires a mating cable (see page 9).
contrast, programming status, and diagnostic warnings • Easy-to-set automatic Expert-style TEACH options† including static, dynamic, and
single-point programming plus manual adjustment for fine-tuning • Smart power-control algorithms to maximize sensing contrast • Fast 500-microsecond sensing response • Programmable 30-millisecond pulse stretcher (OFF delay) • Extreme programming flexibility via two push buttons or a remote input wire • Output may be programmed for either light or dark operate • Bipolar discrete outputs: one current sourcing (PNP) and one current sinking (NPN) • Visible red (660 nm) light source • Easy-to-read TEACH and signal strength readout, plus indicators for a continuous
DISTANCE
page 2
Banner Engineering Corp. • Minneapolis, MN U.S.A. • Tel: 763.544.3164
FI22FP Low-Profile Inline Plastic Fiber Optic Sensor
DISTANCE
0 60 mm 120 mm 180 mm 240 mm 300 mm 2.4 in 4.8 in 7.2 in 9.6 in 12.0 in
DISTANCE
ห้องสมุดไป่ตู้
0 125 mm 250 mm 375 mm 500 mm 625 mm 5.0 in 10.0 in 15.0 in 20.0 in 25.0 in
readout of operating status †U.S. Patent #5,808,296
FI22FP Inline Fiber Optic Sensor Models
Model
Cable*
FI22FP
2 m (6.5') 5-wire integral cable
Supply Voltage Output Type
DISTANCE
Diffuse Mode
1000
E X C E 100 S S
G 10 A I N
1 0.1 mm .004 in
FI22