注塑模具采购合同
Party A ：_______________________ Party B ：_______________________ 签订日______ 年____ 月_____ 日
第 1 页共15 页
The Buyer (Party A )
Address 地址：
Postcode 邮编：
Contacts联系人：
Tel电话：
Fax传真：
The Seller (Party B)
Address 地址：
Postcode 邮编：
Contacts联系人：
Tel电话：
Fax传真：
After frie ndly n egotiati on , Party A and Party B agree to reach this con tract as follows for compl ying with.
甲乙双方经友好协商，甲方和乙方一致同意签订以下合同，以便共同遵守。
乙方根据甲方提供的注塑产品要求负责设计制造模具上述模具单价为人民币含17%税,
包括了模具设计，生产，试模，以及产品在甲方验收合格前的所有相关费用。
Party B should desig n and produce the Molds. The un it price for the molds
mentioned above based on RMB(included 17% vat) ，which includes the design produce ，trial run cost and any other cost about the Molds before the plastics sample have bee n approved by Party A.
2.Quality Sta ndard: the quality of goods shall accord with the sta ndard as
follows:
质量标准：本合同标的物需符合以下质量标准：(可以多选)
According with state standard and industry standard ，if they are not the same the higher shall prevail.
符合国家标准和行业标准，若两者不一致以高者为准。
It must be at least 500, OOOpcs good plastic parts which can be produced by the mold in the con tract.
合同中的模具必须可以生产至少50万模次的合格产品。
The plastic products which are produced by the Molds need to meet the requirement of Party
A ，refer to Appe ndix1 sta ndard of plastic products.
该模具生产的注塑产品应符合甲方的要求，详见附件1注塑产品标准。
3.Lease & Mai ntai n 所有权，租借以及维护保管
3.1 The property of molds will transfer to Party A after inspection and
acceptanee. Party A will decide to lease the Molds to Party B , then Party B shall use them to produce plastic parts in their own factory. In period of lease term , the damageand destroy risk of molds is borne by Party B , Party B should keep the molds in good condition , and bear any cost of maintain.
经甲方验收合格后，模具的所有权即归甲方所有。甲方视情况将模具寄存在乙方工厂并且委托乙方进行注塑加工。租借期内，模具损坏和灭失的风险由乙方承担，乙方有义务保证模具完好，如有损坏需立即维护并且支付相应费用。
3.2 The Molds are the property of Party A ，Party A can carry part of or all
of them back any time.
模具的所有权为甲方，甲方有权随时收回部分或者全部模具。
3.3 Party B shall mark all molds with the designation “” And the parts nu mber.
乙方应在所有合同中的模具上标识“”字样和部件号。
4.Sample 样品
Party B shall provide eno ugh qua ntity of plastic sample which produced by the
Molds in this con tract accordi ng to the appe ndix 1 before mass product ion of
the goods.
乙方应凭合同中的模具生产出按照附件1要求提供足够数量的注塑样品。样品经甲方验
收合格并书面确认之后乙方可凭合同中模具进行批量生产。
5.Delivery 交货
5.1 Place of Delivery: The factory of Seller.
交货地点：乙方工厂
5.2 Delivery Schedule:
交货日期：
Seller shall deliver the Goods in full at the destination as designated by Buyer in a timely way within the time schedule as required in Order , which shall be con cluded and sig ned by the Parties.
乙方按照双方签订的订单所规定的交货时间按时、足额将货物送达甲方指定的交货地
点。
Party B shall delivery all goods on ， if Party B want to delivery before the date ，they shall inform Party A in advanee and be approved by Party A.
乙方应于年月日交付全部货物，乙方若提前交付，需事先通
知甲方，经甲方同意后方能交付。
Others: Party B must finish the mold within 45days after received drawings from Part A，and provide eno ugh qua ntity good plastic samples withi n 50days after received draw ings from Part A.
乙方需在收到甲方图纸65天内制作完毕所有模具，并且在收到甲方图纸70天内前提供
足够数量的合格注塑样品。
5.3 Party B should inform in writte n Party A in days adva nee in case of any delay in delivering the products or providing the service. Party A is