交大方菱数控平面切割控制系统F2300_Ver23_操作手册F2300型数控切割控制系统使用说明书方菱数控切割机控制系统使用手册（Ver.2.3）(型号：F2300)上海交亿数控设备有限公司2022-12i F2300型数控切割控制系统使用说明书目录F2300型数控切割机控制系统使用手册（VER.2.2）..................................................... ..................I 阅读手册.............................................................. ................................................................ ................II 环境要求.............................................................. ................................................................ ................II 维护.............................................................. ................................................................ ........................II 高压电.............................................................. ................................................................ ....................II 注意事项.............................................................. ................................................................ ....................1 开机关机.............................................................. ................................................................ ................1 备份参................................................................ ................2 还原参数.............................................................. ................................................................ ................2 清空代码.............................................................. ................................................................ ................2 系统升级.............................................................. ................................................................ ................3 优盘工作不正常.............................................................. ................................................................ ....3 断电恢复.............................................................. ................................................................ ................3 第一章概述.............................................................. ................................................................ ..............4 1.1系统简介.............................................................. ................................................................ .........4 1.2系统特点.......................................................................4 1.3技术指标.............................................................. ................................................................ .........5 1.4系统接口.............................................................. ................................................................ .........5 1.5硬件配置.............................................................. ................................................................ .........5 第二章系统开机.............................................................. ................................................................ ......6 2.1系统操作面板说明.............................................................. .........................................................6 2.2系统启运及主界面说明.............................................................. .................................................6 2.3主界面功能索引.............................................................. . (9)第三章自动功能.............................................................. ....................................................................10 3.1自动操作索引.............................................................. (1)1 3.2调速.............................................................. ................................................................ ...............12 3.2.1正常调速.............................................................. .. (12)3.2.2快速调速.............................................................. .. (12)3.3空走功能.............................................................. ................................................................ .......12 3.4后退功能/透枪功能.............................................................. .......................................................12 3.5边缘切割/偏移切割/返回.............................................................. .............................................12 3.6图形功能.............................................................. ................................................................ .......13 3.7选行/选号....................................................................14 3.8镜像.............................................................. ................................................................ ...............16 3.9图形旋转/钢板校正.............................................................. ......................................................18 3.10排列.............................................................. ................................................................ .............22 3.11比例.............................................................. ................................................................ .............26 3.12图形还原.............................................................. ................................................................ .....26 iiiF2300型数控切割控制系统使用说明书3.13图形放大/缩小.............................................................. (26)3.14回参功能.............................................................. ................................................................ .....27 3.15退出切割....................................................................27 3.16断电恢复.............................................................. ................................................................ ......27 第四章手动功能.............................................................. ................................................................ ....29 4.1点动功能.............................................................. ................................................................ .......29 4.2连动功能.............................................................. ................................................................ .......30 第五章代码说明.............................................................. ................................................................ ....31 5.1编程符号及说明.............................................................. ..........................................................31 5. 2坐标系统.............................................................. ................................................................ ......31 5.3G代码说明.............................................................. ..................................................................32 5.4M代码说明.............................................................. ................................................................ .37 第六章文件操作.............................................................. ................................................................ ....38 6.1代码操作索引.............................................................. (3)9 6.2本机代码.............................................................. ................................................................ ......39 6.2.1调入代码.............................................................. (3)9 6.2.2删除代码.............................................................. (4)1 6.2.3单拷文件.............................................................. (4)2 6.2.4全拷文件.............................................................. (4)2 6.3U盘文................................................................ ......43 6.4新建代码.............................................................. ................................................................ ......44 6.5代码编辑.............................................................. ................................................................ ......44 6.6编译代码.............................................................. ................................................................ ......45 第七章参数设置.............................................................. ................................................................ ....46 7.1常用参数.............................................................. ................................................................ ......46 7.2氧燃气参数.............................................................. ................................................................ ..47 7.4等离子参数.............................................................. ................................................................ ..48 7.5喷粉参数....................................................................49 7.6系统参数.............................................................. ................................................................ ......50 7.7保存参数.............................................................. ................................................................ ......52 第八章诊断功能.............................................................. ................................................................ ....53 8.1诊断界面索引.............................................................. ................................................................54 8.2输入诊断.............................................................. ................................................................ .......54 8.3输出诊断.............................................................. ................................................................ .......54 第九章图库.............................................................. ................................................................ ............56 9.1选择图形.............................................................. .......................................................................56 9.2片/孔尺寸.............................................................. ................................................................ ......57 第十章接口说明.............................................................. ................................................................ ....59 10.1输入接口.............................................................. ................................................................ .....59 ivF2300型数控切割控制系统使用说明书10.2输出接口.............................................................. ................................................................ .....60 10.3电机接口.............................................................. ................................................................ .....61 第十一章系统配置.............................................................. ................................................................63 11.1系统升级.............................................................. ................................................................ .....63 11.2参数备份、还原.............................................................. ..........................................................64 11.3IO口定义及坐标定义.............................................................. ...............................................65 11.3.1输入口定义.............................................................. ........................................................65 11.3.2输出口定义.............................................................. .........................................................66 11. 3.3坐标定义.............................................................. . (67)11.4系统时间.............................................................. ................................................................ .....68 11.5横/纵向脉冲数.............................................................. (69)vF2300型数控切割系统使用说明书注意事项开机关机1．开机给系统通上DC24V电源接通时，系统自动进入到开机状态。