Tool design approval=模具设计审核
Tool design modification/revision=模具设计更改
Tool parts design (detail) =
模具钣件设计（详细）
Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引
Die set, upper plate=上模架
layout inspection=全尺寸检验
Die inspection & approval=模具检查和审核
Stretch carriers=拉伸运送装置
delivery=发货
Punch stripping plates=冲头压料板
Rejected=拒收
Construction method=结构方法
Preceding into the design=继续设计
Manual Surface Grinder=手动平面磨床
Guidethecoil through the tool=导引卷材
Spotting red=合模用丹红
Checking aid/checking gage=检具
Thin=薄
Tool design=模具设计
Strip design=料条设计
Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口”
Shear=剪切
Forlocatingretainer blocks=承盘键
Sensor=传感器
Forholdingbuttons or pilots=冲母座或导销键
Stretch web=拉伸网
For fixed heel or positive stop=镶根键
Layout the parts=设计钣件
Lower trim inserts retainer=下模切刃块承盘
Assemble inserts=组立镶块
Punch stripping plates=冲头压料板
Assembly=组立
Trim punch backing plates=切刃冲头背板
NC Machining=NC雕刻加工
Stripper window inserts=料条窗户镶块
CMM=三次元测量仪
Symmetric=对称的
The axis of symmetry=对称轴
Technical=技术上的
Diagonal=对角线
Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引
One two three block=一二三模块
Trim punch backing plates=切刃冲头背板
Scrapped=报废
Stripper window inserts=料条窗户镶块
Rework=返工
Heel plates=背托
stop block=停止块
Prepare for delivery=准备发货
Hydro form液压成形
Key=键
FMC Make=保丽龙制作
Construction method=结构方法
modification=更改
Check & measure=检查&测试
Machining=机器加工
Large machining=在大型机器上加工上下模架（铣、车等）
Small machining=在小型机器上加工模块等
Lower die trim inserts=下模切刃块
汽车冲压模具英语词汇
Die / Tool=模具
Prog. Die=progressive diபைடு நூலகம்级进模
Ball bearing guide posts and bushings=球形滚珠导柱和轴套
Casting die=铸造模
Cage=套
Part=钣件
Rigidity=强度
Die material=制模材料
Layout ink=试模用蓝墨水
Jig=夹具
Masking tape=黄色不透明胶带(遮蔽胶带)
Fixture=夹具
Pliers=尖嘴钳，老虎钳
Ball bearing guide posts and bushings=
球形滚珠轴套
Cresent wrench=可调扳手
Guide post=导柱Bushings=导套
Pump pipe=泵管
Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口”
Adjustable parallels=可调平行块
Stop block=阻止块
Granite Table=花岗岩平台
Backing Plate=背板
Plotter=.描绘器, 图形显示器, 绘图器, 坐标自记 器, 标图员
Shoulder Bolt=肩头螺丝
Fitting=研磨组立
Spotting=合模
Die tryout=试模
Cushing stroke=缓冲行程
Dowel pin=定位销
Guide lift pin=导引升降销
Assemble gas spring=安装氮气缸
Stamp parts=冲钣件
Adjustment=调试
Run off parts=冲钣件
Lower trim steels=下刃块
Hit parts=冲钣件
Section=冲头断面
Lifters=提升器
Trim punch=切刃冲头
Coil=卷材
jack screwhole=起重[千斤顶]螺旋孔
Guide block=导引块
Die set, lower plate=下模架
Guide the coil through the tool=导引卷材