豪华油烟机使用说明书中英对照-CAL-FENGHAI.-(YICAI)-Company One1豪华吸油烟机Luxurious Cooker Hood安装说明Installation Instruction1、安装工具准备，①冲击电钻（带钻头)②扳手③螺丝刀④尺1. Prepare installation tools: ①Impact Electric Drill (with drill) ②Spanner ③Screwdriver ④Ruler2、确定位置：吸油烟机平行安装于炉头正上方．底部距炉台安装参考高度650—750mm,可拆卸挡板安装参考尺寸430mm，可根据实际的安装情况适当调整。
安装孔距机体应垂直居中和保持水平。
(如煤气炉灶安装说明规定了较大的安装距离者，对此应予考虑，)例：吊顶装饰罩（无拆卸挡板的安装方法）吊顶装饰罩可拆卸挡板（有拆卸挡板的安装方法）2. Determine Installation Site: the hood should be installed over the cooker. The reference setting distance from the bottom to the cooker is 650-750mm. The reference dimension of the dischargeable baffle plate is 430mm. It can be adjusted according to practical installation situation. The mounting hole should align vertical centers and keep horizontal with the cooker hood.(For instance, if a longer distance is stipulated in the instruction manual of cooker, it should be considered.). suspending ceiling decorative covering (installation method without dischargeable baffle plate )Suspending ceiling decorative covering dischargeable baffle plate (installation method with dischargeable baffle plate )3、安装挂脚：按照挂脚的尺寸在墙壁的相应位置上．钻出直径为8mm （严禁钻孔过大，造成膨胀管松动而意外跌落)．深度为50一60mm的四个孔，将膨胀管压入孔内．再用随机配备的St4X40木螺钉将挂脚可靠固定。
3. Install Hitching Legs: Determine the relevant position on the wall according to the dimensions of the hitching legs. Drill 4 holes with diameter of 8mm (Do not drill holes with too large diameter to prevent accidental fall of cooker hood due to the loose of expansion pipe.) and depth of 50~60 mm. Press the expansion pipe into the holes then fix the hitching legs with St4X40 wood screws accompanied with the machine.4、安装装饰罩：揭去装饰罩保护膜．将装饰罩组件由上向下套入机身。
装饰罩长度若不够．可另行向我公司购买。
4. Install Decorative Covering: Disclose the protective layer of the covering and put it on the body of cooker hood from up to down. If the decorative covering is not long enough, you can purchase from our company.5、安装机体：将机体后部的挂孔对准挂脚的按压滑入．用手晃动机体看是否挂牢。
目测机体下沿应水平。
如不平，可调整固定架之水平。
5. Install the Body of Cooker Hood: Make sure the hanging holes in the back of cooker hood are directed at the hookers of the hitching legs and push the cooker hood to make the hookers slip into the holes. Shake the cooker hood to ensure it isfastened. Estimate the lower edge by eyes, and the cooker hood should be horizontal. If not, you can adjust the mounting bracket.6、安装排风管：将排风管插入止回阀出风口内外圈之间，然后将排风管的另一端接至室外。
6. Install Exhaust Duct: Insert the exhaust duct between inner race and outter race of the air outlet check valve.豪华吸油烟机Luxurious Cooker Hood使用说明Operation Instruction照明强档弱档电源Light High Speed Low Speed PowerI、电机电源开关键“OFF”／“电源”：用来关断油烟机电机电源1. Power Switch button “OFF” / “Power”: Press this button to cut off the power2、油烟机低速档按键“”／“弱档”：控此键，油烟机低速运转。
2. Low Speed button “”/”Low Speed”: Press this button to turn on the cooker hood at low speed3、油烟机高速档按键“”／“强档”：按此键，油烟机高速运转。
3. High Speed button “”/”High Speed”: Press this button to turn on the cooker hood at high speed4、照明灯开关按键“”／“照明”：按此键．可循环开启，关闭照明灯4. Light Switch button“”/”Light”: Press this button to turn on the light, and press again to turn it off.豪华吸油烟机Luxurious Cooker Hood电机电源开关键“OFF”／“电源”：用来关断油烟机电机电源Power Switch button “OFF” / “Power”: Press this button to cut off the power油烟机低速档按键“”／“弱档”：控此键，油烟机低速运转。
Low Speed button “”/”Low Speed”: Press this button to turn on the cooker hood at low speed油烟机高速档按键“”／“强档”：按此键，油烟机高速运转。
High Speed button “”/”High Speed”: Press this button to turn on the cooker hood at high speed照明灯开关按键“”／“照明”：按此键．可循环开启，关闭照明灯Light Switch button “”/”Light”: Press this button to turn on the light, and press again to turn it off.延时功能键控键“”：按此键，启动延时一分钟．油烟机进入低速运转．按电源开关“”或高速键“”．取消延时功能，延时完成后关闭所有电源。
Delay button””/: Press this button to activate the delay function. The cooker hood will continue to operate 1 minute at low speed. To cancel the delay function, pressthe Power Switch button “” or High Speed button“”. After the delay, power will be cut off automatically.照明上调下调快档慢档停止Lighten Upward Downward High Speed Low Speed Stop程序：上电时音乐声．按钮时伴有蜂鸣。
Application: When turning on the power, there are music sounds and when pressing buttons, there are beeps.开关程序功能：Switches Application Function:1、停止键和停止指示灯：停止键作为电机及延时总关键，电机不工作按此键无效。
在电机快或慢工作时停止指示灯亮，电机不工作时停止指示灯不亮。
1. Stop Button and Stop Indicator Lamp: Stop button is the master switch of motor and delay function. If the motor does not work, pressing this button is ineffective. When the motor works with low or high speed, the stop indicator lamp is on. When the motor does not work, the stop indicator lamp is off.2、电机快慢键和电机快慢键指示灯：当按电机快或慢键工作时其相应指示灯及停止，指示灯亮，快慢互锁．当电机工作时，(如：电机快档工作时，再一次按电机快档键电机关机，进入电机工作等待状态。