new: with individual activation of calibration reminder new: also for oxygen
(FW V3.79)
MAS-100 Systems: The leading microbiological air monitoring systems
27
16
16.1
Technical specifications
Environmental conditions
28
29
17 18 19 20 21
21.1 21.2 21.3 21.4 21.5 21.6 21.7 21.8 21.9
Components check list Care and maintenance Warranty Accessories Appendix
1.2
Operating the MAS-100 CG Ex
Read all instruction carefully before operating the instrument. The MAS-100 CG Ex must be operated by specialized laboratory people only.
®
MBV AG Microbiology and Bioanalytic Industriestrasse 9 CH-8712 Stäf Fax +41 44 928 30 89 Mail: info@mbv.ch www.mbv.ch
page 1 of 41 MAS-100 CG Ex_UM_HW_V17_e.docx
9
9 9 10 10 11 11 11 11 11 11 11
6
6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8
Perform air sampling in „Manual Mode 1”
Prepare instrument Working in explosion hazardous zones Prepare the instrument for sampling “Manual sampling” with the MAS-100 CG Ex After the sampling process Switch off the MAS-100 CG Ex Interrupt a measurement Low gas flow
MAS-100 CG Ex User Manual Hardware
MAS-100 CG Ex Professional Microbiological Air Monitoring System for the microbial testing of compressed gases
MAS-100 CG Ex is a registered trademark (MBV AG / Switzerland)
Table of statistical corrections to Feller for SH 300 x 0.6mm Firmware Flow Diagram MAS-100 CG Ex „Manual Mode 1” Firmware Flow Diagram MAS-100 CG Ex „Template-Mode 2” Firmware Flow Diagram MAS-100 CG Ex „Selectable Mode 3 Firmware Flow Diagram MAS-100 CG Ex „Parameter Mode 4” Continue: Firmware Flow Diagram MAS-100 CG Ex „Parameter Mode 4” Firmware Flow Diagram MAS-100 CG Ex „Initial activation of the calibration reminder” EC-Declaration of Conformity ATEX-Certificate
5
5 5 5 5 5 5 5
2 3
3.1 3.2
Introduction Basic principle
Gas flow 100 or 50 litres/min Automatic decompression cycle
6 6
7 7
4
4.1
Most important advantages of the MAS-100 CG Ex
Index
1
1.1 1.2 1.3 1.4 1.5 1.6 1.7
Warning notices
Important Safeguards Operating the MAS-100 CG Ex Charging the MAS-100 CG Ex Directions for use in explosion risk areas and Environmental Conditions Warranty Malfunction of instrument Working with compressed gas in general
Transport trolley
8
8
5
5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11
General functions
Overview Initial start-up of the MAS-100 CG Ex = Activation of calibration reminder Switch ON and OFF the MAS-100 CG Ex Calibration reminder Manual or Template mode Last gas / volume used Change gas type Select other volumes Delay function User menu Sampling
Battery charging Battery status display Battery replacement Vacuum test for MAS-100 CG Ex unit
25 26
26 26 26 26
15
15.1
Calibration
Calibration reminder
27
12
12 12 12 13 14 14 14 14
7
7.1 7.2 7.3
Perform air sampling in „Template Mode 2”
Prepare instrument Working in explosion hazardous zones “Template mode” sampling with the MAS-100 CG Ex
approved by: LF page 4 of 41
1
Warning notices
1.1
Important Safeguards
The Microbiological Air Sampler Type MAS-100 CG Ex may be opened or charged only outside the explosion hazard zone.
1.3
Charging the MAS-100 CG Ex
The Microbiological Air Sampler Type MAS-100 CG Ex may be opened or charged only outside the explosion hazard zone.
1.4 Directions for use in explosion risk areas and Environmental Conditions
16 17
17 17 17 17 17 18 18 18 18 18
MAS-100 CG Ex User Manual Hardware MAS-100 CG Ex_UM_HW_V17_e.docx
valid from: 2014.01.08 version template/document: 2.0 / NA
approved by: LF page 3 of 41
MAS-100 CG Ex User Manual Hardware MAS-100 CG Ex_UM_HW_V17_e.docx
valid from: 2014.01.08 version template/document: 2.0 / NA
15
15 15 16
8 9
9.1 9.2 9.3 9.3.1 9.3.2 9.3.3 9.3.4 9.4 9.5 9.6
Perform air sampling in „Selectable Mode 3” Instrument settings Mode 4
General description Clear protocol data Connecting a printer Basic Information General Printer Settings Printer Citizen CT-S281 Other Printers Print protocol Back to main menu Set time and date
29 29 30 30 30
31 32 33 34 35 36 37 38 39
22
Revision History
41
MAS-100 CG Ex User Manual Hardware MAS-100 CG Ex_UM_HW_V17_e.docx
valid from: 2014.01.08 version template/document: 2.0 / NA