EMC TEST REPORTProduct Description : Mobile BatteryModel No. : BL-4BReport No. : OTE1006001136Test Date : Jun. 18 to 25, 2010Regulations :SeebelowStandards Results (Pass/Fail)EN 61000-6-3: 2007EN 61000-6-1: 2007- IEC 61000-4-2: 2001 - IEC 61000-4-3: 2006 PASS PASS PASS PASSPrepared ForShenzhen Waystrengthen Electronics Technology Co.,Ltd.Bldg 3, Hongye Industrial Park, Lezhujiao, Jiuwei, Xixiang Town, Bao'an District,Shenzhen, Guangdong, China.Prepared ByShenzhen Outest Technology Co., LTD17th Floor, Tianyuan Building, Bao’an 31 District, Shenzhen,Guangdong, China (518101)TEL: 86-755-26415344FAX: 86-755-27841136TABLE OF CONTENTSDESCRIPTION PAGE REPORT DECLARATION 3 SUMMARY OF TEST RESULTS 4 1. GENERAL INFORMATION 5 1.1 SYSTEM DESCRIPTION 5 1.2 SUPPORT EQUIPMENT 5 1.3 TEST FACILITY 51.4 TEST EQUIPMENT LIST 62. EN 61000-6-3 RADIO DISTURBANCE CHARACTERISTICS 7 2.1 MEASUREMENT PROCEDURE & LIMIT (RADIATION EMISSION TEST) 7 2.2 BLOCK DIAGRAM OF TEST SETUP 82.3 SUMMARY DATA 93. EN 61000-6-1 IMMUNITY CHARACTERISTICS12 - IEC 61000-4-2 (ELECTROSTATIC DISCHARGE)3.1 BLOCK DIAGRAM OF TEST SETUP 12 3.2 TEST PROCEDURE 133.3 PERFORMANCE & RESULT 134. EN 61000-6-1 IMMUNITY CHARACTERISTICS15 - IEC 61000-4-3 (RADIATED ELECTROMAGNETIC FIELD)4.1 BLOCK DIAGRAM OF TEST SETUP 15 4.2 TEST PROCEDURE 164.3 PERFORMANCE & RESULT 165. PRODUCT LABELING 17 5.1 PROPOSE CE LABEL FORMAT 17 5.2 PROPOSED LABEL LOCATION ON EUT 17APPENDIX I18 PHOTOGRAPHS OF EUTREPORT DECLARATIONEquipment Under Test: Mobile BatteryModel: BL-4BAdding Models: BL-4L, BL-4U, BL-4C, BL-5B, BL-5C, BP-5M, BL-5F Applicant: Shenzhen Waystrengthen Electronics Technology Co.,Ltd.Bldg 3,Hongye Industrial Park, Lezhujiao, Jiuwei, Xixiang Town,Bao'an District, Shenzhen, Guangdong, China.Manufacturer: Shenzhen Waystrengthen Electronics Technology Co.,Ltd.Bldg 3, Hongye Industrial Park, Lezhujiao, Jiuwei, Xixiang Town,Bao'an District, Shenzhen, Guangdong, China.Type of Test: EMC Directive 2004/108/EC for CE MarkingTechnical Standards: EN 61000-6-3: 2007EN 61000-6-1: 2007- IEC 61000-4-2: 2001- IEC 61000-4-3: 2006File Number: OTE1006001136Date of test: Jun. 18 to 25, 2010Deviation: NoneCondition of Test Sample: NormalThe above equipment was tested by Shenzhen Outest Technology Co., LTD for declaration with the requirements set forth in EMC Directive 2004/108/EC and the Technical Standards mentioned above. This said equipment in the configuration described in this report shows the maximum emission levels emanating from equipment and the level of the immunity endurance of the equipment are within the compliance requirements.The test results of this report relate only to the tested sample identified in this report.Approved by Authorized Signatory:Lab. Director / CabinJun. 25, 2010SUMMARY OF TEST RESULTSDescription of Test ResultRadiated Disturbance Pass Electrostatic Discharge Immunity (ESD) Pass Radiated Electromagnetic Field Immunity Pass1. GENERAL INFORMATION1.1 Description Of EUT1.1.1 Make sure the EUT work normally during the whole test;1.1.2 The EUT technical data: DC 3.7V 600mA1.2 Support EquipmentDevice Type Manufacturer Model NameN/A N/A N/A1.3 Test Facility1.3.1 Location:17th Floor, Tianyuan Building, Bao’an 31 District, Shenzhen City, Guangdong Province, China.1.3.2 Description of Lab.:There is one 3m Semi Anechoic chamber test sites and one line conducted labs forfinal test.The Semi Anechoic chamber and the Line Conducted labs areconstructed and calibrated to meet the FCC requirements in documents ANSIC63.4 and CISPR 22, EN 61000-6-3 requirements1.3.3 Instrument Tolerance:All measuring equipment is in accord with ANSI C63.4 and CISPR 22requirements that meet industry regulatory agency and accreditation agencyrequirement.1.4 Test Equipment ListInstrumentation: The following list contains equipment used at Centre Testing International (China) Limited for testing. The equipment conforms to the CISPR 16-1 / ANSI C63.2 Specifications for Electromagnetic Interference and Field Strength Instrumentation from 10kHz to 1.0GHz or above. Equipment used during the tests:Radiated Disturbance Test Site:Radiated Disturbance TestEquipmentType ManufacturerModelNumberSerialNumberLastCalibrationCalibrationDueSpectrum Analyzer Agilent E4443A N/A 05/27/2010 05/26/2011 Amplifier ETS2090N/A05/27/2010 05/26/2011 Antenna ETS3142CN/A05/27/2010 05/26/2011 Note: The measure uncertainty is less than +/-2.5dBESD Test Site:ESD Test (61000-4-2)EquipmentType ManufacturerModelNumberSerialNumberLastCalibrationCalibrationDueESD Generator SCHAFFNER NSG 432 2014 05/27/2010 05/26/2011R/S Test Site:Radiated Electromagnetic Field immunity Measurement (61000-4-3)EquipmentType ManufacturerModelNumberSerialNumberLastCalibrationCalibrationDueSignal Generator Maconi 2022D 119246/003 05/23/2010 05/22/2011 Power Amplifier M2S A00181/ 10009801-112 05/23/2010 05/22/2011Power Amplifier M2S AC8113/800-250A9801-179 05/23/2010 05/22/2011Power Antenna SCHAFFNER CBL6140A 1204 05/23/2010 05/22/20112. EN 61000-6-3 RADIO DISTURBANCE CHARACTERISTICS2.1 Radiated Emission Test Measurement Procedure & Limit2.1.1 Measurement Procedure2.1.1.1 The equipment was set up as per the test configuration to simulate typical actual usage perthe user’s manual. When the EUT is a tabletop system, a wooden turntable with a height of0.8 meters is used which is placed on the ground plane as per EN 61000-6-3 (see TestFacility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane.2.1.1.2 Support equipment, if needed, was placed as per EN 61000-6-3.2.1.1.3 All I/O cables were positioned to simulate typical actual usage as per EN 61000-6-3.2.1.1.4 Make sure the EUT work normally during the test.2.1.1.5 The antenna was placed at 3 meter or 10 meter away from the EUT as stated in EN61000-6-3. The antenna connected to the Analyzer via a cable and at times a pre-amplifier would be used.2.1.1.6 The Analyzer / Receiver quickly scanned from 30MHz to 1000MHz. The EUT testprogram was started. Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane, in both the vertical and the horizontal polarization, to maximize the emission reading level.2.1.1.7 The following test mode(s) were scanned during the preliminary test:2.1.2 Radiated Emission LimitFrequency (MHz) Distance(m)Maximum Field Strength Limit(dBuV/m/ Q.P.)30-230 3 40.00 230-1000 3 47.00**Note: The lower limit shall apply at the transition frequency.2.2 Block Diagram Of Test SetupBattery EUT :MobileModel :BL-4BTechnical data DC 3.7V 600mA2.2.1 Radiation Emission Test2.3 Summary DataRadiated Emission TestTest Result: PASSOriginal Data:Test Mode: NormalTemperature: 24o C Humidity: 48%RHLocation: 3m Semi-anechoic Chamber(The chart below shows the readings taken from the Original data)Frequency Reading(Peak) Correct Result Limit Margin Remark(MHz) (dBuV) Factor(dB)(dBuV) (dBuV) (dB)200.0432 24.68 6.58 31.26 40.00 -8.74 H134.0194 26.85 4.32 31.17 40.00 -8.83 H31.9586 21.09 6.77 27.86 40.00 -12.14 H363.5231 21.00 10.95 31.95 47.00 -15.05 H620.1167 21.01 14.24 35.25 47.00 -11.75 H-14.63 V 363.5231 21.42 10.95 32.37 47.00-16.86 V 261.2730 21.16 8.98 30.14 47.00-15.83 V 172.5976 19.09 5.08 24.17 40.00-14.42 V 134.0194 21.26 4.32 25.58 40.00-12.12 V31.9586 21.11 6.77 27.88 40.00**NOTE: “---” denotes the emission level was or more than 2dB below the Average limit, so no re-check anymore.Freq. = Emission frequency in MHzRaw Data (dBuV) = Uncorrected Analyzer / Receiver readingCorr. Factor (dB) = Correction factors of antenna factor and cable lossEmiss. Level = Raw reading converted to dBuV and CF addedLimit dBuV = Limit stated in standardMargin dB = Reading in reference to limitReadingPK =PeakQP =Quasi-peakPlot of Radiation Emissions Test DataRadiated EmissionEUT: Mobile BatteryM/N: BL-4BOperating Condition: RunningTest Specification: HorizontalPlot of Radiation Emissions Test DataRadiated EmissionEUT: Mobile BatteryM/N: BL-4BOperating Condition: RunningTest Specification: Vertical3. EN 61000-6-1 IMMUNITY CHARACTERISTICS – IEC 61000-4-2 ELECTROSTATIC DISCHARGE (ESD) IMMUNITY TESTTest Result : PASSBasic Standard : IEC 61000-4-2: 2001Test Level : ± 8 kV (Air Discharge)± 4 kV (Contact Discharge)± 4 kV (Indirect Discharge)Performance Criteria : B (Standard Require)25o C/50%RHTemperature/Humidity :3.1 Block Diagram Of Test Setup( The 470 k ohm resistors are installed per standard requirement ) ArrayGround Reference Plane3.2 Test Procedure3.2 1 The EUT was located 0.1 m minimum from all side of the HCP.3.2.2 The support units were located 1 m minimum away from the EUT.3.2.3 Make sure EUT worked normally.3.2.4 Active the communication function if the EUT with such port(s).3.2.5 As per the requirement of IEC 61000-4-2; applying direct contact discharge at the sides otherthan front of EUT at minimum 20 discharges (10 positive and 10 negative) if applicable, can’t be applied direct contact discharge side of EUT then the indirect discharge shall be applied.3.2.6 Other parts of EUT where it is not possible to perform contact discharge then selectingappropriate points of EUT for air discharge, a minimum of 10 single air discharges shall be applied.3.3 Performance & ResultThe electrostatic discharges were applied as follows:Table 1: Electrostatic Discharge Immunity (Air Discharge)EN 61000-4-2Test Levels (kV)Test Points -2 +2 -4 +4 -6 +6 -8 +8 -15 +15Surface A A A A A A A ATable 2: Electrostatic Discharge Immunity (Direct Contact)EN 61000-4-2Test Levels (kV)Test Points -2 +2 -4 +4 -6 +6 -8 +8 -15 +15 / / / / /Table 3: Electrostatic Discharge Immunity (Indirect Contact HCP)EN 61000-4-2Test Levels (kV)Test Points -2 +2 -4 +4 -6 +6 -8 +8 -15 +15Front Side A A A ATop Side A A A ABack Side A A A ALeft Side A A A ARight Side A A A ATable 4: Electrostatic Discharge Immunity (Indirect Contact VCP) EN 61000-4-2Test Levels (kV)Test Points -2 +2 -4 +4 -6 +6 -8 +8 -15 +15Front Side A A A ATop Side A A A ABack Side A A A ALeft Side A A A ARight Side A A A APerformance Criteria:A.The apparatus shall continue to operate as intended during and after the test. Themanufacturer specifies some minimum performance level. The performance level may bespecified by the manufacturer as a permissible loss of performance.B.The apparatus shall continue to operate as intended after the test. This indicates that the EUTdoes not need to function at normal performance levels during the test, but must recover.Again some minimal performance is defined by the manufacture. No change in operatingstate or loss or data is permitted.C.Temporary loss of function is allowed. Operation of the EUT may stop as long as it is eitherautomatically reset or can be manually restored by operation of the controls.4. EN 61000-6-1 IMMUNITY CHARACTERISTICS – IEC 61000-4-3 RADIATED ELECTROMAGNETIC FIELD IMMUNITY TESTTest Result : PASSEnclosurePort :Basic Standard : IEC 61000-4-3: 2006Test Level : 3 V/m with 80% AM.1kHz ModulationSteps: 1 % of fundamentalDwell Time: 1 secPerformance Criteria : A (Standard Require)25o C/51%RHTemperature/Humidity :4.1 Block Diagram Of Test Setup4.2 Test Procedure4.2.1 The EUT was located at the edge of supporting table keep 3 meter away from transmittingantenna, it just the calibrated square area of field uniformity. The support units were located outside of the uniformity area, but the cable(s) connected with EUT were exposed to the calibrated field as per IEC 61000-4-3.4.2.2 Make sure EUT work normally.4.2.3 Setting the testing parameters of RS test software per IEC 61000-4-3.4.2.4 Choose the worst side of EUT for final test from 80 MHz to 1000 MHz at 1% steps.4.2.5 Recording the test result in following table.Range (MHz) Field Modulation Polarity PositionResult (Criteria)80-1000 3V/m Yes H Front A 80-1000 3V/m Yes H Back A80-1000 3V/m Yes H Left A 80-1000 3V/m Yes H Right A 80-1000 3V/m Yes V Front A 80-1000 3V/m Yes V Back A80-1000 3V/m Yes V Left A 80-1000 3V/m Yes V Right A4.3 Performance & Result:A. The apparatus shall continue to operate as intended during and after the test. Themanufacturer specifies some minimum performance level. The performance level may bespecified by the manufacturer as a permissible loss of performance.B.The apparatus shall continue to operate as intended after the test. This indicates that the EUTdoes not need to function at normal performance levels during the test, but must recover.Again some minimal performance is defined by the manufacture. No change in operatingstate or loss or data is permitted.C.Temporary loss of function is allowed. Operation of the EUT may stop as long as it is eitherautomatically reset or can be manually restored by operation of the controls.5. PRODUCT LABELING5.1 Propose CE Label FormatSpecifications: Text is Black in color and is right justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT and the user manual.5.2 Proposed Label Location on EUTCE LabelAPPENDIX I PHOTOGRAPHS OF EUTFigure 1General Appearance of the EUTFigure 2General Appearance of the EUT。