复合材料英汉双语词汇Acetyl||乙酰Acid-proof paint||耐酸涂料, 耐酸油漆Acrylic fiber||丙烯酸纤维Acrylic resin||丙烯酸树脂Active filler||活性填料Adapter assembly||接头组件Addition polyimide||加成型聚酰亚胺Addition polymer||加聚物Adjusting valve||调整阀，调节阀Adhersion assembly||粘合装配Adhersion bond||胶结Adjustable-bedpress||工作台可调式压力机Adjuster shim||调整垫片Adjusting accuracy||调整精度，调校精度Admissible error||容许误差Admissible load||容许载荷Adsorbed layer||吸附层Advanced compositematerial||先进复合材料，高级复合材料Advanced developmentvehicle||试制车，预研样车AE(AutomobileEngineering)||汽车工程技术Aeolotropic material||各向异性材料Aerated plastics||泡沫塑料, 多孔塑料Aerodynamic body||流线型车身Aft cross member||底盘/车架后横梁Air bleeder||排气孔Air clamp||气动夹具Air deflector||导流板；导风板，气流偏转板Air intake manifold||进气歧管Air servo||伺服气泵Air-tight joint||气密接头All-plastic molded||全塑模注的All polysterseat||全聚酯座椅Alligatoring||龟裂，涂膜皱皮,表面裂痕Amino resin||氨基树脂Angular test||挠曲试验Anti-chippingprimer||抗破裂底漆（底层涂料）Apron||防护挡板Aramid fibrecomposites||芳胺纤维复合材料Assembly drawing||装配图Assembly jig||装配夹具Assembly part||装配件，组合件Autoclave forming||热压罐成型Autocorrection||自动校正Automatic compensation||自动补偿Automatic feed||自动进料Automobile instrument||汽车仪表板Automotive transmission||汽车传动装置，汽车变速器Auxiliary fasiaconsole||副仪表板Axial strain||轴向应变Axle bushing||轴衬Axle fairing||底盘车桥整流罩A Stage||A 阶段(某些热固性树脂聚合作用的初期阶段) AAC(AuxiliaryAir Control)||辅助空气控制ABC(Active BodyControl)||主动式车身控制装置Abherent||阻粘剂Ability meter||测力计，性能测试仪ABL (Ablative)||烧蚀剂Ablation||烧蚀Ablative compositematerial||烧蚀复合材料Ablative insulativematerial||烧蚀绝热材料Ablative polymer||烧蚀聚合物Ablative prepreg||烧蚀性预浸料Ablative resistance||耐烧蚀性ABR(AcrylateButadience Rubber)||丙烯酸丁二烯橡胶Abradant material||研磨材料，磨料Abrade||研磨；用喷砂清理Abrasion||磨耗Abrasion coefficient||磨耗系数Abrasion loss||磨耗量，磨损量Abrasion performance||磨耗性Abrasion-proofmaterial||耐磨材料Abrasion resistantpaint||耐磨涂料Abrasion test||磨损试验Abrasive blastsystem||喷砂清理系统Abrasive cloth||砂布Abrasive disc||砂轮盘，砂轮片Abrasive finishing||抛光Abrasive ***||砂纸Abrasive resistance||耐磨性ABS(AcrylonitrileButadiene Styrene)resin||ABS树脂，丙烯腈-丁二烯-苯乙烯(热塑性)树脂ABSM(AmericanBureau of Standard Materials)||美国标准材料局Absolute dynamicmodulus||绝对动态模量Absolute error||绝对误差Absorbent material||吸收性材料,吸收性物质，吸声材料，吸收剂Absorber||减振器，阻尼器，缓冲器ACA(AutomotiveComposite Alliance)||汽车复合材料协会ACC(AutomaticClutch Control)||自动离合器操纵控制Accelerant||促进剂，加速剂Accelerated agingtest||加速老化试验，人工老化试验Accelerator pedalshaft||加速踏板轴Accelerator pumpnozzle||加速泵喷嘴Acceptable life||有效使用寿命Acceptance testspecification||验收测试规范Access panel||罩板,盖板Accessory||配件，附属品Accessory equipment||辅助设备Accessory kit||附件包，成套附件Accumulator can||储电池外壳Accumulator package||蓄压器组件，蓄压器单元Accuracy in calibration||校准精度Accuracy of finish||最终加工精度Accuracy of manufacture||制造精度Accuracy of positioning||定位精度Accuracy of repetition||重现精度，复制精度Acetal matrixcomposites||缩醛树脂基复合材料Acetal plastic||缩醛塑料,聚甲醛塑料Acetal resin||缩醛树脂Acetamide||乙酰胺Acetate fiber||醋酸纤维，乙酸纤维Acetone||丙酮Back corner panel||后围角板Back panel||后围板Back side panel||后侧板Back wall pillar||后围立柱Backer||衬料Baffler||挡板，阻尼器；导流叶片Bag Molding||气囊施压成型(袋模法) Baggage holder||行李架Barrier coat||阻挡层；防渗涂层Batch mixing||分批混合，批混Batching unit||分批加料装置Bearing assembly||轴承组合件Biaxial winding||双角缠绕, 双轴缠绕Binder fiber||粘合纤维Bipolymer||二元共聚物Bismaleimidecomposites||双马来酰亚胺复合材料Blank placement||坯料的放置Blanket||玻璃纤维毡；坯料Blanking press||冲压机, 冲割压力机Blending resin||掺合树脂BMC(Bulk MouldingCompound)||团状膜塑料BMI (Bismaleimide)||双马来酰亚胺Body back panel||车身后板Body back wall||车身驾驶室后围Body bracket||车身支架Body controlmodule||车身控制模块Body frame (Bodyskeleton)||车身骨架Body front panel||车身驾驶室前围板Body monocoque||单壳体车身，单壳式结构车身Body outer panel||驾驶室覆盖件；驾驶室覆盖件Body structuralmember||车身结构件Body trim||车身装饰件Bonded rivetedstructure||胶铆结构Bonnet||发动机罩Brake||制动器Brake arrangement||制动装置Brinell hardnesstest||布氏硬度试验Brittle coating||脆性涂层Bulk coat||整体涂层Bulk heat treatment||整体热处理Bulk mouldingcompound||(增强塑料)预制整体模塑料Bumper bracket(holder)||保险杠托架Bus brake system||客车制动系Butt flange||对接法兰Butt joint||对接接头；对接Butterfly valve||节流阀，节气门BWI (Body InWhite)||白车身Cab deflectorshield||驾驶室导流板Cab fairing||驾驶室整流罩Cab floor||驾驶室地板Cab mounting||驾驶室悬置CAD(ComputerAided Design)||计算机辅助设计CAE (ComputerAided Engineering)||计算机辅助工程设计Calibration tolerance||校准公差Calibrating instrument||校准仪表Camouflage paint||覆面漆, 盖面涂料, 伪假漆Cantilever beamimpact test||悬臂梁冲击试验Carbon-felt reinforcedcarbon composites||碳毡增强碳复合材料Carbon fiberclutch||碳纤维离合器Carbon filamentcloth||碳丝织物Case extension||外壳的伸出部分，延伸外壳Casing gasket||外壳密封垫Catalyst manifold||固化剂总成Catalyst pump||固化剂泵Catalyst ratio||固化剂比率Cavity||模槽，型腔；凹模Cavity block||阴模Cavity depth||模槽深度Cellular board||蜂窝状板，多孔板Cellular plastics||泡沫塑料，多孔塑料Centre boss||轮毂Centre pin||销轴，枢轴，主销Centrifugal castingmoulding||离心浇铸成型Centrosymmetry||中心对称层板Ceramic matrixcomposites||陶瓷基复合材料Charge||填充气体，填充料Chasis||底盘；机壳，车架Chlorinated polyethlene||聚氯乙烯Chopped fiber||短切纤维Chopped randommat||短切无序毡Chopped strand||短切原丝CIRTM(Co-InjectionRTM)||共注射RTMClamping fixture||夹具，夹紧装置Clamping force||夹持力，合模力Class A su***ce||A级表面Clear coat||透明涂层，透明罩漆，清漆层Clear coat finish||清漆涂层Clicker die||冲模Climb milling||同向铣削, 顺铣Clipping press||切边压力机Closure pressingspeed||合模速度CMM(Closed MouldMoulding)||闭合模塑CMT(CompressionMolding||挤压成型工艺CNC(ComputerizedNumerical Control）||电脑数值控制Coarse grinding||粗磨，用砂轮初加工Coating defect||涂层缺陷Collision test||碰撞试验，撞车试验Combination property||综合性能Concept design||概念设计Convection modulus||对流模量Convergence test||收敛试验Cooling fixture||冷却夹具Cooling tower||冷却塔Crazing||龟裂，细裂纹Cresol resin||甲酚树脂Cutting felt||毡的剪切Cutting-off bushing||环形下料模; 下料环Damped structure||阻尼缓冲结构Damper bracket||件振器支架Dashboard illumination||仪表板照明Dash trimming||前围板衬板Deburring||去毛刺，倒角，除飞边Deepdrawing forming||深拉成型Deflection test||挠曲试验Dent resistance||耐冲击性Design freedom||设计自由度Detail drawing||祥图，零件图Die assembly||压模装置Die casting||压模铸件,压模铸法Dimethyl fomamide||二甲基甲酰胺Dimethyl ketone||二甲基甲酮; 丙酮Dip pretreatment||浸渍预处理Die prime coat||浸渍打底漆Dimensional stability||尺寸稳定性Dip coating||浸涂Dip forming||浸渍成型Durability testing||耐久性试验，寿命试验Dwell||保压,暂停加压；滞留时间Dynamometer||测力计Edge effect||边缘效应，边界效应Edge feed||边缘进料Edge gate||侧浇口Ejection force||脱模力Ejector||起模杆Ejector guidepillar||推板导套Ejector housing||支架Elasticizer||增塑剂Elastomeric composites||高弹体复合材料Elongation atbreak||断裂延伸率Energy absorbingfoam||吸能泡沫塑料Epoxy resin||环氧树脂Ether ketone||酮醚Explosion proof||防爆Exterior bodypanelling||车身外板部蒙皮Exterior trim||外饰，外饰件Fabric composites||织物复合材料Fabric impregnation||织物浸渍Fabric preform.|织物预成型Fabric prereg||织物预浸料Fabrication parameter||制造参数Fabrication procedure||制造工序Fabricating machinery||加工设备Face plate coupling||法兰式连接Factory primer||工厂底漆，工厂防锈漆Fairing||整流罩，整流装置Fairing panel||前裙板Fascia bracket||仪表板支架Fascia mask||仪表板罩板Fastening clamp||夹紧装置，紧固夹子Fatigue tensiontest||拉伸疲劳性试验FCM(Fibrous Compositematerial)||纤维复合材料FEA(Finite ElementAnlysis)||有限元分析Feed system||供料系统Feeding pump||供给泵Feeding speed||进给速度Female groove||凹模Female mould(tooling)||阴模Fender||翼子板；护板Fender apron||挡泥板Fender innerpanel||翼子板内衬护板Fiber compositelaminate||纤维复合材料层板Fiber mat layer||纤维毡层Finisher(Finishingcomponent)||装饰件Flange||法兰, 凸缘Flange fitting||法兰式管接头Flash||毛边Flash mold||毛边模具Front sheet metal||车前板制件Fuselage fairing||机身整流装置Gage kit||仪表组，仪表套件Gas cavity||气泡，砂眼Gauge panel||仪表板Gear assembly||齿轮传动装置, 减速器Gearbox cover||变速器壳盖Gear bracketsupport||齿轮托支架Gel coat||胶衣,凝胶涂层Gel coat drum||胶衣圆桶Gel coat flowmonitor||胶衣流量监控器Gel time||凝胶时间Glass fiber windingmachine||玻璃纤维缠绕机Glass wool||玻璃棉Glass yarn||玻璃丝Guiding device||导向装置Gunk||预混料Gusset||角撑件Gutter channel||流水槽Hand lay-up ||手工铺叠，手工铺贴Hardness testingmachine||硬度测试仪Hauling truck||拖车Header boardoutside panel||前板外板Headrest||靠枕Heat barriermaterial||隔热材料Heat forming||热成型High molecularmaterial||高分子材料High pressurebag molding||高压袋成型工艺High pressureinjection moulding||高压注射成型，高压注射模塑High-strengthstructural adhesives||高强度结构粘合剂High temperaturecoating||高温涂层Hose support||软管支架Hub assembly||毂组件Hub bearing||车轮轮毂轴承Hydraulic device||液压装置Hydraulic engine||液压发动机Hydrostatic strength||流体静力强度IMC(In-Mold Coating)||模具内部涂层Immersion paint||浸漆Immersion test||浸渍试验，浸泡试验Immovable support||固定刀架Impact analysis||碰撞试验撞击分析Impact bending||冲击挠曲Impact specimen||冲击试样Impegnate||浸渍Impelling strength||冲击韧性Injection head||注射头Injection-mouldedcomposites||注射模塑复合材料Injection mouldedpart||注塑制件Injection nozzle||注射喷口，压注喷口Intermittententry||间歇供给，不连续供给Intermittentfailure||间接性故障Izod test||悬臂冲击试验Jack||千斤顶，起重器；传动装置Jack engine||辅助发动机Jackbit insert||切刀，刀具，刃口Jacket||护套，套管，保护罩，蒙皮Jar-proof||防震的Jaw||钳口；定位销Jell||胶凝，凝固，固结Jet milling||喷射研磨Jig||夹具，定位模具Jig-adjusted||粗调的Job program||工作程序Joining nipple||接合螺管Joining on butt||对头接合Joint face ofa pattern||分模面Joint gate||分型面内浇口Joint packing||填充垫圈，接合填密Joint sealingmaterial||填缝料Joint-shapedsupport||铰接支架Joint strenght||连接强度Jump welded tube||对缝焊管，焊接管Junction bolt||接合螺栓Junction point||接点Keeping life||保存期，产品有效期Kenel||型芯Ketene||乙烯酮, 烯酮Ketene dimethyl||二甲酮Ketimide||酰基酮亚胺Ketimine||酮亚胺Ketoamine||酮胺，氨基酮Ketol||乙酮醇Ketone||甲酮Keying strength||咬合强度Knife holder||刀具，刀架Knockout||脱模Knockout pin||脱模销Knockout plate||脱模板Knoop scale||努氏硬度标度Knuckle joint||铰链连接Koplon||高湿模量粘胶纤维Koroseal||氯乙烯树脂Lacquer||挥发性漆；涂漆Lacquer finish||喷漆，上漆，罩光Lacquer formation||漆膜形成，成漆Lacquer putty||腻子，整面用油灰Lacquering ||上清漆Laminate constructionthickness||结构层厚度Laminated panel||薄层状板Laminated plastics||层压塑料制品, 塑料层板Laminated thermosettingplastics||层压热固塑料Latex paints||清漆Lay-up||(塑料，夹板的)铺叠成型Light-alloy bodypart||轻合金车身零件Lining ||衬里，衬垫Loaded haul cycle||载货行程Location bearing||定位轴承Location guide||固定导杆，定位导杆Location hole||定位孔Location tolerance||位置公差, 安装公差Locatin pin||定位销Lock bolt||锁紧螺钉Low pressureinjection moulding||低压模塑成型Low shrink resin||低收缩树脂Luggage rack||行李架Machining accuracy||加工精度Machining center||加工中心Main shaft gearbushing||主轴齿轮衬套Mandrel ||卷芯，模芯；芯轴Manifold hood||歧管外罩Manual Lay-Up||人工手糊Manual spray-up||手工喷射Manual truck||手推车Manufacturingdrawing||制造图纸Matched molds||合模Matrix ||基体，基质Mechanical properties||机械性能Metal bonding||金属粘结Metal-workingmachine||金属加工机床Methanol||甲醇Mismachiningtolerance||加工误差Modular||组装式的Mofulus of elasticity||弹性模量Mould operation||模具操作Moulded plastics||模压塑料Moulding||嵌条；成型；装饰件Mount support||装配支架Multi-axial stress||多轴向应力Multi-tool machining||多刀切削加工Needled mat||针刺毡，针织毡Non-ductile fracture||无塑性破坏Nontwisting fiber||不加捻纤维Notched izodtest||带缺口悬臂梁式冲击试验Nozzle||管嘴，喷嘴Numerically controlledengine lathe||数控普通车床Nylon resin||尼龙树脂OEM (OriginalEquipment Manufacturer) ||原始设备生产商Offset cab||侧置驾驶室On-site forming||现场发泡On-site winding||现场缠绕成型Open molding||敞开式模塑法Opening mould||开模Optimized design||优化设计Orifice||注孔Orthophenyl tolylketone||邻苯基甲苯基酮Orthophthalicresin ortho||邻苯二甲酸树脂Osmotic pressure||渗透压力Outboard wing||外翼Outer panel skin||蒙皮Oven heating||烘箱加热，加热固化Over-engineering||过份设计的Over flow||溢流Over-spray||过喷Overhead travelingcrane||高空移动行车Overhead-valveengine||顶置气门发动机Overhung trailer||外伸式拖车Oxide paint||氧化物涂料Package power||动力装置总成Packed ||紧密的，密实的；有密封的，有填料的Packing||衬垫；填料，密封填料；包装PAD(Paint AsRequired)||按需涂漆Paint base coat||上底漆Paint blemish||涂漆缺陷Paint blower||喷漆用压力机，喷漆枪Paint brush||涂漆刷Paint dilution||油漆稀释PE(Polyethlene)||聚乙烯Pedestal mounted||落地安装的Phenolic plastic||酚醛塑料Phenyl ketone||苯基甲酮Pit mounted||嵌入式安装Pivotal arm||枢轴Platic structuralcomponent||塑料结构零部件Plastic upholstery||(座椅)塑料蒙面Play compensation||间隙补偿PLC(ProgrammableLogical Controller) ||可编程序逻辑控制器Polycarbonateplastics||聚碳酸脂塑料Polyester resin||聚脂树脂Polyimide||聚酰亚胺Polymer||聚合物，高分子，多聚体Polyurethanefoam||聚氨酯泡沫塑料Polyvinyl||聚乙烯的, 聚乙烯Polyvinyl fluoride||聚氟乙烯Prefabricatedparts||成品零部件，制造好的零部件Propylene resin||丙烯类树脂Protecting lacquer||防护漆PSF(PolystyreneFoam)||聚苯乙烯泡沫塑料PTFE(Polytetrafluoroethylene)||聚四氟乙烯Pultrusion||拉挤成型Putty knife||油灰（腻子）刮铲QC(Quality Control)||质量控制QCS(Quality ControlStandard)||质量管理控制标准QR(Quality Requirements)||质量规格Quality certification||质量认证Quantity production||大量（成批）生产，大规模生产Quantity production||大量（成批）生产，大规模生产Quarter panelbrace||后侧围板支撑件Quarter panellower extension||后侧围板下延伸部Quarter trimcap||后侧围装饰板盖Quarte wheelhouse||后侧围轮滚罩，后侧围车轮室Quasi-isotropiclaminate||准各向同性层板Quench||淬火Rack truck||架子车, 移动架Radial dispersion||径向位移Radial loading||径向力(载荷)Radial pump||径向离心泵Radiation protectivepaint||防辐射涂料Radiator||散热器Rag||毛刺RARTM(Rubber-assistedRTM)||橡胶辅助RTM(用橡胶取代芯材的热膨胀RTM) Reactive resin||活性树脂, 反应型树脂Rear skirt rail||后围裙边梁Reciprocatingengine||活塞式发动机, 往复式发动机Reinforcement||车身加强件，增强材料；构架Repeat accuracy||重复精确度Repeatability||设备重复定位精度Resin formulation||树脂配方Retaining nest||定位槽Return trip||回程，返回行程Rib||筋，加强筋RIFT(Resin InfusionUnder Flexible Tooling)||挠性上模具树脂浸渍工艺RIM(ReactionInjection Molding)||反应注射模塑Safety hood||安全罩Sample testing||样品试验Sand wet||(车身/涂装)湿砂打磨Sandwich body||夹层结构车身Sandwich construction||夹层结构Sandwich panel||多层板，复合板Shaft assembly||轴组件Skin coat||表层；罩面层Solvent reclaim||溶剂的回收Stiffener||加强件Storage modulus||储能模量Stress at definiteelongation||定伸应力Stretched actylicplastic||拉伸丙烯酸塑料String milling||连续铣削Stroke||(悬架)减振器，冲程Structural instrumentpanel||结构仪表板Structural layer||结构层Styrene||苯乙烯Styrofoam||聚苯乙烯泡沫塑料Su***ce mat||表面薄毡Synthetic resinpaint||合成树脂涂料Tack strength||粘着强度Tail gate||(卡车等的)后挡板Teflon||聚四氟乙烯(塑料, 绝缘材料)TERTM(Thermal-ExpansionResin Transfer Molding)||热膨胀树脂传递模塑Thermoplasticplastics||热塑性塑料Thermoset resin||热固性树脂Thickening agent||增粘剂Trim waste||内饰废料Trimming orientation||修边定位Turbulent heating||湍流加热Turndown ratio||衰减比率Twisting stress||扭胁强, 扭应力U bolt||U形螺栓U bolt plate||U形螺栓垫板Ultimate mechanicalstrength||极限机械强度Ultraviolentsensitive coating||紫外线感光涂层Undercoat paint||头道漆Uniaxial drawing||单轴拉伸Unsaturated polyesterresin||非饱和聚酯树脂Unyielding support||不可压缩支架, 刚性支架Upper yield stress||上屈服应力Urethane coating||氨基甲酸乙酯涂层UVRTM(Ultra-violetRTM)||紫外线固化RTM（利用紫外线进行固化）VA RTM (VacuumAssisted Resin Transfer Molding) ||真空辅助RTM Vacuum bag molding||真空袋模制法VARI(Vacuum AssistedResin njection)||真空辅助树脂注射Variable speed||无级变速Ventilation duct||通风管Ventilator(Ventilatingequipment)||通风装置Vibratory stress||振动应力VIMP (VariableInfusion Molding Process)||可变浸渍模塑Vinyl chlorideresin||聚氯乙烯树脂VOC(VolatileOrganic Compound)||挥发性有机化合物Volume modulus||体积模数Vortex generator||(车身)扰流器，导流板VRV(Vacuum ReducerValve)||真空减压阀Warping stress||翘曲应力Waste utilization||废物利用，废物处理Water shield||防水罩，挡泥板；密封条Water tolerance||耐水性Wedge gripping||楔形夹具Wheel fender||翼子板Wing trussgrid||翼子（挡泥）板加强件Winding||缠绕Wingtip assembly||翼尖整流罩Wire drawing||拉丝Wiring press||卷边压力机, 嵌线卷边机Workpiece grippe||工件夹子（持器），机械手Woven rovingfabric||（玻璃纤维）无捻粗纱布织物Xylenol CarboxylicAcid||二甲苯酚酸Xlylene||亚二甲苯基Xyster||刮刀X alloy||铜铝合金Xenidium||胶合板Xenidium||胶合板Xylene ||二甲苯Xylene resin||二甲苯树脂Yard-crane||移动吊车，场内移动起重机Yarn count||纱线支数，丝线支数Yarn strength||纱线强度，长丝强度Yield limit||屈服极限，屈服点Yield point underbending stress||弯曲应力下的屈服点Yield stress||屈服应力, 屈服点Yield stresscontrolled bonding||屈服应力粘结Zedeflon||四氟乙烯均聚物Zero checker||定零位装置, 零位校验Zero clearance||零间隙Zero compensation||零位补偿Zero initialcondition||零初始条件Zero setting||(仪表)零位调整, 置零Zero shrinkageresin||零收缩树脂Zone control||区域控制高分子专业必备英语词汇1 高分子macromolecule, polymer 又称"大分子"。