中文1英文三板模3-Plat Mold
加速項Accelerated Ejector 不乾膠Adhesive Sticker 氣頂Air Poppet Valve 困氣Air Trapping
斜針Angle Pin
斜導柱（斜邊）Angle Pin
A板A'plate
回針板Backup
隔水片Baffle
波子螺絲（行位定位螺絲）Ball-Catch
扁頂Blade
柱子Bosse
B板B'plate
制模Build Mold
緩衝器Bumper
導套Bushing
型腔數Cav
上模鑲件Cavity Block
上模小鑲件Cavity Sub-Insert 倒角Chamfer
碼模槽Clamp Slot
空隙槽Clearance Slot
客戶Client
冷料#Cold Sllig
補償Compensation
配件Components
連續的Consecutive
輪廊Contour
下模鑲件Core Block
Core Pin
下模小鑲件Core Sub-Insert
蓋板Cover Plate
重要尺寸Critical Dimension 剖面圖Cross Sectlon
襯墊Cushion
脫開Cut Of Positon
日期印Dating Insert
設計筒圖Design Preliminary 尺寸Dimension
銪針Dowel
管釘（定位銷）Dowel Pin
出模斜波Draft
出模角Draft
拋光Draw Polish
早回Early Ejector Return
火花機,電火花Edm
頂棍Ejctor
頂針Ejector Pin
頂針板Ejector Plate
頂針底板Ejector Retainer Plate
司筒Ejector Sleeve
漏電Ele Leakage
電動安全開關Electrical Safety Switch
接合Engage
雕刻Engrave
三板模延伸式唧嘴Extension Nozzle Bushing 螺牙1/2-13Eye Bolt 1/2-13Tap
螺紋Eyebolt Thread
倒園Fillet
走水不平均Filling Uneven
精磨Finished
連接件Fittings
凸緣、法蘭Flange
披峰Flash
括花（擦傷）Galling
入水Gate
齒輪Gear
壓條,鉤槽Gib
導向針Guide Din
頂針板導套Guided Ejection Bushing
針板導柱Guided Ejection Leader Pin 三角撐Gusset
手動滑塊Hand Slide
手動滑塊模具Hand Slide-In Txpe Mold
裝卸孔Handl Ing Hole
加硬Hapden
高產量模量High Volume Running Mold 熱嘴Hot Nozzle
油唧Hydraulic Cylinder
注塑模In Jection Mold
替換鑲件Interchangeable Mold Inserts 斜度鎖Interlock
壓緊塊（鏟機）Jaw
落單會議Kick-Off Meeting
頂出板Knock -Out Plate
導柱Leader Pin
導柱及導套Leader Pin Bushing
導柱位Leader Pin Location 漏水測試Leak Test
斜頂Lifter
定位圈（法蘭）Locating Ring
鎖定位Lock
下模水口鐵Lower Runner Bar
熱流道Manifold
膠料Materlal
模胚Mold Base
模具結構Mold Construction
鑲件Mold Insfrt
模號Mold No
運輸安全帶Moldstrap
氮化Nitrided
偏移量Offset
‘O’令（密封圈）O'Ring
平面度Parallel
掛成品Part Hanging
產品名Part Name
產品編號Part No
模芯Parting Core
分型面Parting Line
分模面Parting Surface
局部視圖Partlal View
喉塞Plug
模框鑲件Pocket Insert
拋光Polishing
撬模腳Ppy Slot
預先決定Preload
壓機Press
壓力Pressure
環保印Recycling Insert
加強筋Reinforcing
墊板Retainer Plate
墊板Retainer Plate
回針板Retainer Plate
回針Return Pin
版本標識Revision Level
重新加工Reworked
水口鐵Runner Bar
截水口鑲件Runner Shut-Off Insert
水口板導套Runner Stripper Plate Bushing 水口板導套Runner Stripper Plate Bushing 流道排氣Runner Vents
鎖範本Safety Bar
吊環Safety Holst Ring
試板Sampling
走不齊Short Shot
有托頂針Shoulder Ejector Pin
縮水Shrinkage
合模Shutoff
擦位Shut-Off(S/0)
側抽芯Side Action
直身鎖Side Lock
絲印Silkprint
縮水Sink Mark
突然性動作Slam
司筒
行位Slide
行位鑲件Slide Insert
方鐵（墊鐵）Spacer Block
指定噸位的注塑機Specific Press
彈簧Spring
唧嘴Sprlie
唧嘴Sprue Bushing
水口勾針Sprue Puller Pin
水口拉鉤Spuer Pulzer
粘前模Sticking Cav
粘後模Sticking Core
粘水口Sticking Sprue
材料清單Stock List
拉圾釘Stop Pin
回針Stop Pin
頂白Stress Mark
三打螺絲毫（限螺絲）Stripper Bolt
推板Stripper Plate
小鑲件Sub-Insert
二級頂出針Sub-Leaderd Pin
吸針Sucker Pin
撐頭Support Pillar
控制開關Switch
螺紋孔Tapping Hole
耐落膠Teflon Paste
溫度Temperature
蝕紋Texture
曬紋Texturing
探熱針Thermocouple
成型熱固性塑膠模具Thermoset Mold 通框Through Window 名稱塊表Title Block
公差Tolerance
不規則四邊形Trapeaold
管狀管釘Tubular Dowel
倒扣Under-Cut
上模水口鐵Upper Runner Bar 版本Version
變形Warpage
墊圈Washer
水嘴接頭Water Fittings
漏水Water Leakage
水塞Water Line Pllig 硬片（摩擦片）Wear Plate
楔子Wedge
熔接線Weildline
夾水紋Weld Line
熔接線（夾水紋）Weldline
線切割Wire E.D.M.
線切割Wire-Cut
1．Top clamping plate 2.Top runner plate
3.Cavity plate
4.Core plate
5.support block
6.Ejector ret plate
7.Ejector plate
8.Bottom clamping plate
10.sprue puller pin 21.cavity
22.core.
23.core insert 24.Ejector Pin 9.sprue bushing。