信赖性测试报告 Reliability test report
名称规格/Name specification：
Tester Test group 测试 step 组 测试步骤 1 TestDescription 测试描述 Initial examination of product 初态产品检查 Procedure 程序 EIA-364-18. Visual and dimensional (C of C) inspection per product drawing. Load cable module into cage/connector assembly applied to PCB with attached bezel. Apply specified axial load to engaged module at a maximum rate of 6.35 mm [.25 in] per minute and hold for 1 minute to verify module retention and cage latch strength.
8
Mechanical shock 机械冲击
No damage 无损伤
因受设备限制，暂时无法进行试验
10
Transceiver extraction force 光模块拔出力
30N maximum.
11
Final examination of EIA-364-18. product Visual inspection. 末态产品检查 Initial examination of product 初态产品检查 EIA-364-18. Visual and dimensional (C of C) inspection per product drawing.
7 2组
Random vibration 随机振动
No damage 无损伤
因受设备限制，暂时无法进行试验
2组 EIA-364-27. Condition H. Subject mated specimens to 30 G's half-sine shock pulses of 11milliseconds duration. Three shocks in each direction applied along 3 mutually perpendicular planes, 18 total shocks. EIA-364-13. Measure force necessary to extract the transceiver from the receptacle with kickout springs inoperable at a maximum rate of 12.7 mm [.5 in] per minute.
90 N minimum
4
Final examination of EIA-364-18. product Visual inspection. 末态产品检查 Initial examination of product 初态产品检查 Transceiver insertion force 光模块插入力 EIA-364-18. Visual and dimensional (C of C) inspection per product drawing. EIA-364-13. Measure force necessary to insert the transceiver into the receptacle with kickout springs inoperable at a maximum rate of 12.7 mm [.5 in]per minute. EIA-364-9. Mate and unmate specimens for 100 cycles at a maximum rate of 500 cycles per hour with cage latch operable. EIA-364-28. Test Condition VII, Condition Letter D. Subject mated specimens to 3.10 G's rms between 20 to 500 Hz. Fifteen minutes in each of 3 mutually perpendicular planes.
Meets visual requirements. 符合产品外观的要求 Meets requirements of product drawing. 符合产品图纸的要求 30N maximum
OK
OK
OK
OK
OK
1
OK
OK
OK
OK
OK
2
4 3组 6
Press-fit insertion Measure force necessary to press the specimen onto the PCB into proper seating force location at a maximum rate of 12.7 mm [.5 单PIN压接力 in] per minute. EIA-364-17. Temperature life Method A, Test Condition 4. Subject 温度寿命 specimens mated to blank transceivers to 105°C for 240 hours. Humidity/temperature EIA-364-31. cycling. Subject mated specimens to 10 cycles (10 湿度/温度循环 days) between 25 and 65°C at 80 to 100% RH. Measure force necessary to extract the Press-fit extraction specimen from the PCB at a maximum rate of force 单PIN保持力 12.7 mm [.5 in] per minute. Final examination of EIA-364-18. product Visual inspection. 末态产品检查 Initial examination of product 初态产品检查 EIA-364-18. Visual and dimensional (C of C) inspection per product drawing.
OK
OK
OK
OK
OK
Final examination of EIA-364-18. product Visual inspection. 末态产品检查
OK
OK
OK
OK
OK
备注：信赖性测试报告按产品规格书测试要求进行测试，随机振动、机械冲击、冷热冲击、混合气体等试验，因受设备限制，暂时无法进行试验，如有特殊要求，可委外测试。
No damage 无损伤
No damage 无损伤
8
8 N minimum Meets visual requirements. 符合产品外观的要求 Meets requirements of product drawing. 符合产品图纸的要求
9
OK
OK
OK
OK
OK
1
OK
OK
OK
OK
OK
4组
3
易拓料号/Excelstor part number：
Requirement 要求 Meets requirements of product drawing. 符合产品图纸的要求 测试结果Test result 1 OK 2 OK 3 OK 4 OK 5 OK
1组
3
Cage latch strength 舌片强度
Meets visual requirements. 符合产品外观的要求 Meets requirements of product drawing. 符合产品图纸的要求
OK
OK
OK
OK
OK
1
OK
OK
OK
OK
OK
2
40N maximum.
4
Durability 耐久性
插入力： 40 N maximum 拔出力： 30 N maximum
核准/Approval： 审核/Review： 测试员/Test controler： 日期/Date: 报告编号/Report no：
Temperature life 温度寿命
EIA-364-17. Method A, Test Condition 4. Subject specimens mated to blank transceivers to 105°C for 240 hours.
No damage 无损伤 Meets visual requirements. 符合产品外观的要求 Meets requirements of product drawing. 符合产品图纸的要求
15
Final examination of EIA-364-18. product Visual inspection. 末态产品检查 Initial examination of product 初态产品检查 EIA-364-18. Visual and dimensional (C of C) inspection per product drawing. EIA-364-32. Test Condition VII.Subject mated specimens to 5 cycles between -55 and 105°C with 30 minute dwells at temperature extremes and 1 minute transition between temperatures.