1.保护,保护装置―――protection
保护事件protection event、
SOE事件Soe Records
一般事件General Event
保护事件描述发生错误protection event description error
保护报警protection alarm
保护动作protection operated
保护出口protection operated 在印度，保护动作与保护出口没有区分，是同一个事情
保护复归protection reset
保护类型码device type code 翻译中，装置类型码和保护类型码均如此翻译
2.线路保护―――110KV及以上线路保护、220KV及以上线路保护
line protection - ---110KV line protection, 220KV and above line protection
3.变压器保护―――两卷变压器保护、三卷变压器保护
transformer protection - two-winding transformer protection, three-winding transformer protection
4.间隔―――公用间隔、主变间隔、线路间隔
bay ---- public bay, main transformer bay, line bay
间隔浏览bay browsing
5.二次回路secondary circuit
二次回路正常secondary circuit normal
二次回路断开secondary circuit abnormal
6.开关―――开关操作、开关检修、开关信号breaker or circuit breaker(CB)
breaker –breaker operation, Breaker Maintenance, breaker status
开关分breaker trip
开关合breaker close
开关信号变位breaker status change
开关刀闸变位Break/isolator change
7.刀闸isolator
8.地刀earth switch
就地合闸local close isolator、
就地跳闸local trip isolator、
远方合闸命令remote close isolator
远方跳闸命令remote trip isolator、
合闸成功closing success、
合闸失败closing failure、
跳闸成功tripping success、
跳闸失败tripping failure
9.CT 断线CT line-break
10.PT 断线PT line-break
11.母线bus
12.闭锁―――闭锁功能block - blocking function
闭锁退出lock disable
闭锁投入lock enable
13.就地―――就地状态local state
14.远方―――远方状态remote state (L/R)
15.正常/故障/检修normal/fault/maintenance
16.压板―――strap
普通压板common strap、
备自投压板back-up power strap、
压板退出strap disable
压板投入strap enable
17.比例―――比例系数ratio
18.模拟量analog
19.开关量digital
20.遥测量―――通用遥测analog general analog
虚拟遥测点virtual analog
21.遥控量―――control 通用遥控general control
22.遥脉量energy
虚拟遥脉点virtual Energy
23.遥信量―――digital signal, DS
通用遥信– general DS
虚拟遥信点virtual DS
双位置遥信DPI double point information
遥信变位DS change
开关遥信复归时间Reset TIme of Changed DS (Sec.)
24.电流current (I)
25.电压―――voltage (V)
节点1越限电压– node 1 overvoltage
26.电度energy
27.功率因数power factor (cos )
28.无功reactive power (Q)
29.有功active power (P)
30.直流Direct Current (DC.)
31.电笛alarm whistle
32.电铃alarm bell
电铃时间Alarm Bell Time(Sec.)
分鸣电笛trip whistle
合鸣电笛close whistle
音响驱动电铃电笛sound signal drive alarm bell and alarm whistle 在印度保护本身驱动三种声音，后台只发一种声音
33.开入digital input DI
34.开出―――digital output DO
开出传动– digital output drive
开出板端子digital output board outlet
35.收回―――开出板端子收回、开出超时未收回
reset –digital output board outlet reset DO overtime
36.调压―――voltage regulation
调压成功voltage regulation success、
调压失败voltage regulation failure、
调压升档tap raise、
调压降档tap lower、
调压滑档、tap slip
滑档时间、
调压停止（调压停档）voltage regulation-stop position,、
37.档位―――position
分接头档位– tap position、
中心档位central position
分接头―――tap
分接头调节– tap changing
38.变电站―――substation
变电站类型Station Type
变电站信号复归substation signal reset
变电站信号变位substation signal change
站长station manager、
正值operator on duty、
值长operation in charge
39.零漂―――零漂校验出错zero drift – zero drift calibration error
40.控制字control word
41.死区dead zone ,
42.切除fault clearing
43.防抖动时间Debouncing Delay
防抖动时间变位次数Change Count During Debouncing Delay ,
44.定值
下传定值send setting group to protection
定值区CRC自检出错CRC check error of setting group
定值区出错setting group error
定值模板setting template
定值类型码setting type code
45.CPU告警CPU alarm
装置告警device alarm
1.
2.ROM区和校验出错check sum of ROM error
3.配置信息校验出错configuration check error
4.RAM自检出错RAM self-check error
5.配置表自检出错configuration table self-check error
6.PLC表自检出错PLC table self-check error
7.EEPROM自检出错EEPROM self-check error
8.开出检验出错digital output check error
9.通信中断communication break
10.串口通信中断serial communication break
11.AD采样出错A/D sampling error
383 组号group no 385 功能码function code 386 对象号object no 384 路数route num
46.五防fail-safe unit。