This series controller characteristicsMicrocomputer control system, the operation is easy, humanization, intelligent, fully functional.But also according to customer's unique features of the proposed change, to meet customer demand.Controller can be stored 40 don't product (material), single shaft type 10 section (step) of each product data, biaxial models each product 5 period of winding data (step), can also according to customer requirements to extension.This series controller with inverter, ac motor, brushless dc motor, brushless dc motor with types of semi-automatic, automatic winding machine (CNC) controller.High quality machine please placed in ventilated good place, is conducive to work long hours cooling machine.Please check prior to power supply voltage, be sure to pick up good ground, prevent to get an electric shock.Are strictly prohibited in the corrosive gas, wet space is engaged in the coiling machine operation, lest cause circuit failure, damage to the machine.Prohibit any object fall into the machine, easy to cause short circuit.Any part of the maintenance, can only be conducted by professional maintenance personnel.The controller panel instruction:Stand by work brake slow start high speed brake time entranceType fragement No turns slow stop low speed slow up timeProduction speed direction0-9.: ten keys to input values to use, the key of the second function is as follows:1: in the standby state, press the output minus 12: in standby state, press this button for two seconds production automatic reset3: in standby state, press this button to brake and loosen the switch4: in standby and operating condition can click this button to achieve growth5: in standby and operating condition can click this button to achieve deceleration6: in standby and press this button yield under the running condition and rotational speed switching7: in standby state or pause, press this button force into the next order8: when in standby state or pause, press this button turn of the last step in the sequence9: in the standby mode by pressing this button shows the PO, at this point can be input data;This number is winding laps reset after display turns time or the time interval of two step sequence automaticallyFunction keys:Settings: used to enter or exit the data setDirection: in the condition of setting used to switch motors is reflectionBiaxial machine in standby state, press this button and the two shaft according to the switchClear: when setting data into the current data or to the next item data editorA: under the set state press this button to return on a data editingData display lamp:Type don't: relative to the serial number of a certain type of product, the range is 0 to 40Dan: for what a certain type will divide the step sequence, range of 1 to 10Laps: the winding circle Lou, range of 0.0-99999Slow rev: rev. After the first with slow winding circle number, range of 0.0-25.5 timesSlow stop: before the arrival of the total number of laps, down to a slow circle numerical ahead of time, range of 0.0-25.5 timesLow: rev around slow and stop the slow speed value, range of 0-99%Braking time: winding is complete brake work time, range of 0.0 to 0.0 secondsGently laps: from running at low speed to high speed running laps, the larger the value, accelerated the longer range of 0-99Status display lamp:Standby: the light is on standby, dawn said coiling, or in the editor, flash pauseOperation: the light is said is winding, bright for coiling not stopBrake: the light is working for brakes, not bright for the brake didn't workProduction: the light is currently "production/velocity" display window for productionSpeed: the light of current "production/velocity" display window for the rotational speed (RPM) Direction: motor to reverse the light is bright, don't light motor for clockwise rotationLED digital display:Dan model panel: display Dan coiling step or edit the order at present.Information display: displaying the value of all information, input the actual winding turns.Production/speed display: display complete production or the current winding speed (RPM).Internal data setOperation mode selection: in standby mode press the "a" key for more than 2 seconds to press the "set key," Dan is type screen and data display shows seven digits set data, the model of operation set if you want to change, please press "a", let the decimal point lights up, this time from right to left can be divided into the press 1 to 7 numeric keys to modify its Settings, modify complete press "enter" button, can return to the standby state.Continuous activation: The open is set to 1, 0 closed. In addition to the first step after each step of the same type will automatically start in a row, the setting of time interval for the PO, if PO to 0 or single step sequence and doesn't work.2. Automatically to the number of turns, is set to 1, start button at any time can run to the set number of turns. This feature is especially suitable for quantity has reached setting and then back in a few laps, and then to start running laps. If use this feature is best slow stop ring number and low speed, so as not to run too fast positioning is not allowed.3: the standby4: start point move: this is set to 1 stop button can also start winding: when coiling machine idle, press thestop button, and remain, the startup winding, wire loosen the stop button machine stop immediately;Set 0 to shut down.5 double activation: this is set to 1 for dual boot, boot of pedal switch, and after work, then a foot switch, stop;Is set to 0 to start, just click on the pedal switch has been running to the end.6 to start at the same time: biaxial model is set to 1 start at the same time, two axis 0 means that the two start shaft in turn7 start automatically: open is set to 1, 0 closed. In addition to the product of the first paragraph, the remaining paragraphs will automatically start winding, to the end of the last paragraph is to start with the first paragraph, start time interval between paragraphs set a time for the PO;Unless you press "stop" or "clear" button to stop winding, otherwise will have been working on.Clear all data set: in standby mode press the "a" key and then press "clear" key for more than 2 seconds, the display shows data - DEL - in flashing, once again, press "clear" button shows at this time - DEL a few seconds, after the above steps: all of the winding information will be removed. Please be careful to use this function so as not to remove all the data set.Winding data editorIn standby mode, press the "set" key to start editing coiling data. Step sequence display shows the current model, type indicator light will flash at the same time;Followed by grade, the corresponding indicator light will flash;Then there is data display shows the grade of the total number of laps and circle indicator, at that point can be input data or does not change the original data;Then press "enter" button to enter the next parameter Settings,If you want to change a parameter can press "a" key on the return on a reset, according to the above, and so on, enter the required data at this point, if press the "start" key winding production according to the information editing by opportunity.Data stored in the order as follows:Type Dan don't -- -- -- -- laps - slow and slow stop, high speed, low speed - brake time -- -- -- -- -- -- gently turns the inputexamplesA single step:Requirements:Use the wire diameter: 0.08 mmCircle number: 180Operation mode:1 open the power switch2 set shape fitting: by setting by 1 first, then press enter3 set Dan: according to the N (single step and multiple step is the difference here) according to the input4 input to the total number of laps: press 1 8 0 as input5 input slow rev laps: according to 2 according to the input line is fine6 input slow stop laps: according to zero according to the input7 enter the percentage: according to 99 according to the input8 input low percentage of low speed: according to 5 according to the input9 input braking time: according to 0.3 or. 3 press type brake press 0 if you press enter10 input gently laps: according to 20 according to the input line is fine11 out of the setting status: according to the set(note the direction of the motor in into the lap of Settings you can change it, the type and grade cannot be correct.)More steps:Requirements:Use unified wire diameter, product points three steps winding, specific as followsThe first step in the sequence: 120 laps, speed was 80%, the need to slow startThe second step sequence: turns 60 laps, speed of 50%The third order "for 56 times, speed was 99%, the slow and 2 lapsOperation mode:1 set shape fitting: according to set according to2 first, then press enterDan set 2: according to 3 according to input this paragraph a screen 13 input the first step in order to the total number of ring: according to 1 2 0 according to input4 enter the first step in the slow rev laps: by 0 by input or directly by input5 enter the first step in the slow stop laps: by 0 by input or directly by inputInput the first high-speed percentage: according to 80 according to the input7 enter the percentage of the first step in a low-speed: according to 5 according to the inputThe first step braking time: 8 input according to 0.3 or. If according to the input has been brake by 0 by input or directly by input9: enter the first step in the slow rise turns by 10 input at this time paragraph a screen 210 to enter the second order to the total number of ring: 6 0 in accordance with the input11.Enter the second step is slow to the total number of ring: by 0 by input or directly by inputSlow stop turns12 to enter the second step: according to zero input or directly according to the input13 percentage of high-speed input the second step: according to 50 according to the input14 percentage of low-speed input the second step: according to 5 according to the inputBraking time15 input the second step: according to 0.3 or. 3 press type brake press 0 if you press enter or press enter directly16 input the second step sequence to the total number of laps: by 0 by input or directly by input at this time paragraph 317 input the third order to the total number of ring: according to 5 6 according to the inputInput the third step slow rev laps: 18 by 0 by input or directly by inputEnter the third step slow stop laps: according to 2 according to the input20 percentage of high-speed input the third step: according to 99 according to the inputLow percentage of 21 to enter the third step: according to 5 according to the input22 braking time input the third step: according to 0.3 or. 3 press type brake press 0 if you press enter or press enter directlyStep 3: gently turns 23 input by 0 by input or directly by input at this time paragraph a screen 124 out of data editing status: according to the setWhile carrying out their functions, the controller if found any abnormal situation, will automatically stop running and output error data in the data displayed on the screenERR - 0: memory lost information, to detect when the phone is switched onERR - 4: motor overload when a load is overweight, this error occurred while motor overload, stop winding at the same time;Or when the controller parameter setting is not correct (miss), when the direction ofcounting motor rotate in opposite directions, also can appear error.。