11/4/2020
______________________________________ ____________
4
Part No 8V21-A18A344
Provide car line
with150mm pitch,
Up date the changes and sent 将修改后的设计发送给我们，然后 me the updated data then 进行制造。
JBM Auto System
Trim line marking for 所有检具划修边线 all checking fixture
11/4/2020
______________________________________ ____________
Min line should be “Tolerance
JBM Auto System
11/4/2020
______________________________________ ____________
5
Part No CN15- N40308
Provide car line
Up date the changes and sent me the updated data then
Up date the changes and sent me the updated data then
Please Go for manufacturing
将修改后的设计发送给我们，然后 进行制造。
Provide Swivel form check template min two numbers. See
7
ThTihsilsalnadnd should be shinocureldasbeed by 3 mm so intchraetavsaerdiabtyion in burring 3(Fmlamngseo) tchaantbe measured
该区域高度加高3mm ，以便于能够检测到 毛刺（翻边）。
Please Go for manufacturing
Provide Swivel form check template min two numbers. See
with150mm pitch, part clamping as
per LD data
slide no 2
将修改后的设计发送给我们，然后 进行制造。
slide no 2
至少应有两个样板刀。参 照图片2
Provide car line with150 mm pitch,
应有汽车坐标，并以 150mm 为间距 。
JBM Auto System
11/4/2020
______________________________________ ____________
B515 Checking Fixture Phase II
Huangyan
Date 15-10-11
B515 检具-黄岩
JBM Auto System
11/4/2020
______________________________________ ____________
1
Swivel form check template min two numbers Provided
至少应有两个样板刀。参 照图片2
应有汽车坐标，并以 150mm 为间距，零件 夹持应符合零件检测 的要求。
JBM______________________________ ____________
6
Part No CN15-N40324-A
specified in cad”
最小修边线的公差应 符合图纸的要求。
3
A- You provided diamond pin it is not acceptable please provide tapper pin with minimum and maximum tolerance
B- You provided straight pin instead of that please provide tapper pin with minimum and maximum
至少应有两个样板刀
JBM Auto System
11/4/2020
______________________________________ ____________
2
Nominal line
名义修边线
Part
板件
Max line 3mm from nominal line
距离名义修边线 3mm的最大修边线
将修改后的设计发送给我们，然后 进行制造。
应有汽车坐标，并以 150mm 为间距 。
Provide car line with150mm pitch,
Provide Swivel form check template min two numbers. See
JBM Auto System
11/4/2020
______________________________________ ____________
8
Part No CN15-N1407
Up date the changes and sent me the updated data then
Please Go for manufacturing
part clamping as per LD data
Please Go for manufacturing
Provide Swivel form check
template min two numbers. See slide
NO 2
至少应有两个样板刀。参 照图片2
应有汽车坐标，并以 150mm 为间距，零件 夹持应符合零件检测 的要求。
tolerance as shown in the figure
Round pin
圆销
A
1.你方采用菱形销，是不可以的，请采用锥形销，并给出最大和 最小公差。
2.不要采用直销，请采用锥形销，并给出最大和最小公差。
Min tolerance
最小公差
B
Max tolerance
最大公差
Part
板件
JBM Auto System