white mark silver flow mark
burn mark black spot sticking weld flash
alarm safety gate emergency stop color change purge material resin thermal heat up air shot try mold release mold release agent rust preventatives
英语
injection moldier machine
toke-out robot dryer hopper dryer crushing mill
gas injection \AGI machine
中国语
注塑机
机械手.产品取 出机 干燥机 料斗干燥机 粉碎机
吹气成形.气辅 成形 机械 机器
英语crystalli源自e polymersurface grinder grinding drilling
平面磨床 钻床
flash damage cracking jetting deform warping bend torsion uecnceevnetnricowloarll thickness boid cell stripes
dirty flaking tear off float screw damage shortage
中国语 程序控制
英语 over packing
工艺.工序.过程
注塑工艺程序控制装 置
注塑程序控制装 置
冷料井
冷料.旱凝料 冷凝
液压.油压
液压顶出.液压脱 模
液压泵
液压马达
空压机(空气压缩 机)
漏油
油箱. 活塞
气缸
mold mark
shock
damage sink mark short shot flash string flash
runout contraction assembly NG stress internal stress preparation
英语 stopper stripper spacer plate mould base puller lock support plate support pillar
electric discharge machine wire EDM nitriced steel nitrogen nitricdize titanium haet treatment hardening temper annealing prehaden hardness soft electrodes insert slide taper draft guider bush guider pin sleeve pin square pin angular ejector
mold closing speed
injection speed injection capacity charging charging stroke
nozzle nozzle head tie bar/tie rod
射嘴,喷嘴 射嘴头 喷嘴 拉杆,拉扛
rib insert wall thickness
polymer injection condition injection molding cycle precision injection
set the condition mold set-up
screw screw head joint injection feeder compound blend mixer mixing cooling cooling tower
(产品)无法脱模.粘 模
注.射.啤 浇口 中心浇口 注口.流道料 间隔
注流道. 注(塑) 口 流道. 流道料 散气孔.通风口 排气 热处理 .退火
英语 mold machining center universal milling machine lathe\turning
中国语 模具 加工中心 铣床 车床
can't release shot gate center gate sprue runner clearance
sprue runner air vent breathing anneal
报警 安全门 紧急停止 换色 清机胶料.过料 胶料温度 升温.升热 空射胶.空打 试模 脱模 脱模剂 防锈剂
料筒(注塑机 的) 加热器,发热器 加热圈.热器带 热电偶
mold down pressure low pressure low pressure clamping holding time back pressure clamping force hold clamping pressure clamping stroke clamping unit mold opening
distance between\tie rods limit switch operation guide control panel automatic semi auto hand handle extruder extrusion molding blow molding machine blow molding
英语 program control
process
injectvisor
injectrol cold slug well cold slug freeze hydraulic
hydraulic ejector hydraulic hydraulic motor
air compressor oil leakage oil tank piston air cylinder
chiller temperature controller
cylinder heater band heater thermocouple
螺杆.螺丝.螺旋 螺杆头 接头.接缝 注塑.注射 送料(加料)器 混炼料.化合料 混合.搅拌 混合器.搅拌器 混合.搅拌 冷却 冷却塔
冷水机.冷水装 置 温调机
拉杆间隔 操作开关 操作指南 控制器 控制盘 全自动 半自动 手动 手柄 操纵 押出机 挤塑机 挤塑 吹塑机 吹塑
plastication thermal decomposition shrinkage resin material plastics tubber master batch powder dry color pgelallsestfiber\fibrous glass hose