Terminal Reviews to English for the Automotive ProfessionI. Answer the following questions.(20%)Choose 5 of 6, 4 points for each, total in 20 points.1. What does the drive train consist of?The drive train consists of clutch, transmission, driveshafts, differentials, and the final drive (drive wheels, continuous track like with tanks or Caterpillar tractors, propeller, etc.). In a wider sense, the drive train includes all of its components used to transform stored (chemical, solar, nuclear, kinetic, potential, etc) energy into kinetic energy for propulsion purposes.2. How to install the drive gear?First, clean the drive gear attaching bolts. Second, remove the adhesive adhered to the threaded holes of the drive gear by turning the special tool, and then clean the treaded holes by applying compressed air. Third, apply the specified adhesive to the threaded holes of the drive gear. Forth, install the drive gear onto the differential case with the mating marks properly aligned. Tighten the bolts to the specified torque in a diagonal sequence.3. What is the process of the ABS working?The Anti-lock Brake System (ABS) uses a sensor that know when one wheel (or a pair of wheels) is skidding. The sensor sends a signal to a computer, which signals a modulator valve. The modulator connects into the hydraulic system and can momentarily release the brake pressure and prevent the wheels from locking. (The pressure release is so fast that a driver is seldom aware of it.) Pressure is then reapplied until the sensor again sensor that the wheel is about to lock up. Thus, this system keeps the wheels as colse to lock up as possible, without actually allowing the wheels to lock up and skid. This is called incipient lock up. Maximum braking occurs at that point.4. What is the purpose of gear reduction from steering gear?The gear reduction is known as steering gear ratio. This is needed to reduce the amount of effort required to turn the steering wheel, particularly when parking. During straight-ahead driving, this also reduces the possiblility of oversteering. The ratios vary considerably, depending largely on vehicle size and weight. Larger, heavier vehicles require a graeter reduction in manual steering gears.5. How does the starter clutch work?The purpose of the starter clutch is to engage and disengage the pinion gear from the flywheel. When the starer is cranking, the pinion gear slides on the armature shaft and engages the flywheel.6. How to check DTC in the normal mode?First, turn ignition switch off. Second, connect terminals TE1 and E1 of data link connector 1 or 2. Third, Turn ignition switch on. Forth, read the diagnostic trouble code on malfuntion indicator lamp on the combination meter. Fifth, afer completing the check, turn ignition switch off and disconnect terminals TE1 and E1.II. Translate the following into Chinese. (20%)Choose 20 of 30, 1 points for each, total in 20 points.1. drive train 动力传动系2. suspension system and axle 悬挂系统和驱动桥3. brake system 制动系统4. steering system 转向系统5. automatic transmission diagnosis system 自动变速诊断系统6. intermediate connector 中间连接器7. on-board diagnotics 车载诊断8. data link connector 数据链路连接器/故障诊断连接器9. torque converter clutch (液力)变矩器锁止离合器10. vinyl hose 乙烯软管11. pitman arm 转向摇臂12. tab washer 有耳垫圈13. phanton view 透视图14. steering knuckle 转向节15. recirculating ball guide 循环滚珠导管16. pivot lever 转轴杆17. solenoid valve 电磁阀18. caliper body 制动钳体19. brake drum 制动鼓20. steering axis inclination 主销内倾角21. side scuffing 侧向磨损22. multipurpose grease 多效润滑油23. propeller shaft 传动轴24. ring gear 从动锥齿轮/环形齿轮25. drive pinion rear bearing inner race 主动锥齿轮后轴承内座圈26. oil pressure gauge 油压表27. anchor plug 定位销28. diaphragm spring 膜片弹簧29. splined hub 花键毂30. governor 调速器III. Translate the following into English. (20%)Choose 20 of 30, 1 points for each, total in 20 points.1. 驱动桥总成transaxle assembly2. 液压制动助力器hydraulic brake booster3. 输入轴转速传感器input shaft speed sensor4. 从动盘总成driven plate assembly5. 主减速器从动齿轮final drive ring gear6. 泵轮impeller7. 强制降档制动带kickdown band8. 棘爪弹簧detent spring9. 蓄能器活塞accumulator piston10. 机油滤网oil strainer11. 止推轴承thrust bearing12. 倒档齿圈reverse annulus gear13. 减压制动器reduction brake14. 凸缘轮companion flange15. 放油螺塞drain plug16. 扭转振动torsional vibration17. 比例阀proportioning valve18. 电子控制单元electronic control unit (ECU)19. 自动变速器用油automatic transmission fluid (ATF)20. 制动块和磨损指示总成pad and wear indicator assembly21. 轮缸wheel cylinder22. 控制器局域网controller area network (CAN)23. 动力控制模块power control module (PCM)24. 蜗轮和球螺母总成worm gear and ball nut assembly25. 转向横拉杆tie-rod26. 转向轴轴承调节器steering shaft bearing adjuster27. 摇臂轴花键spines for pitman arm28. 齿扇轴sector shaft29. 动力缸左腔left turn power chamber30. 齿条总成rack bearingIV. Translate the following sentences into Chinese. (20%)Choose 5 of 6, 4 points for each, total in 20 points.1. The most common compound planetary gear sets are the Simpson compound planetary gear set and the Ravigneaux compound planetary gear train.最常见的复合行星齿轮组是辛普森复合行星齿轮组和拉威诺复合行星齿轮系。